3.12.3 FriendlyElec NanoPi R5C Factory Installation to eMMC Logs
Here is the complete debug output for booting and running from the SD card the image for initial factory system installation to the internal eMMC flash memory.
DDR Version V1.13 20220218
In
ddrconfig:0
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: 48ps, dqs1: -120ps, dqs2: 48ps, dqs3: -48ps,
change to: 324MHz
PHY drv:clk:36,ca:36,DQ:29,odt:0
vrefinner:24%, vrefout:41%
dram drv:40,odt:0
clk skew:0x61
change to: 528MHz
PHY drv:clk:36,ca:36,DQ:29,odt:0
vrefinner:24%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
change to: 780MHz
PHY drv:clk:36,ca:36,DQ:29,odt:0
vrefinner:24%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
change to: 1560MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x1c
cs 0:
the read training result:
DQS0:0x33, DQS1:0x33, DQS2:0x33, DQS3:0x39,
min : 0xa 0xd 0x10 0xd 0x2 0x6 0x8 0x7 , 0x4 0x2 0xc 0xf 0xe 0x11 0x13 0x11 ,
0xe 0xc 0xb 0x8 0x2 0x2 0x4 0x6 , 0xb 0xa 0x7 0x2 0x10 0xf 0x11 0xd ,
mid :0x25 0x27 0x2a 0x27 0x1b 0x20 0x23 0x21 ,0x1f 0x1e 0x27 0x2b 0x29 0x2d 0x2d 0x2d ,
0x2a 0x28 0x26 0x23 0x1e 0x1e 0x1f 0x21 ,0x26 0x25 0x23 0x1d 0x2b 0x2b 0x2d 0x29 ,
max :0x41 0x42 0x45 0x42 0x35 0x3b 0x3e 0x3c ,0x3b 0x3a 0x42 0x47 0x45 0x49 0x48 0x49 ,
0x46 0x45 0x41 0x3f 0x3a 0x3b 0x3b 0x3d ,0x42 0x41 0x3f 0x38 0x47 0x47 0x4a 0x45 ,
range:0x37 0x35 0x35 0x35 0x33 0x35 0x36 0x35 ,0x37 0x38 0x36 0x38 0x37 0x38 0x35 0x38 ,
0x38 0x39 0x36 0x37 0x38 0x39 0x37 0x37 ,0x37 0x37 0x38 0x36 0x37 0x38 0x39 0x38 ,
the write training result:
DQS0:0x25, DQS1:0x5, DQS2:0x25, DQS3:0x13,
min :0x71 0x74 0x77 0x76 0x67 0x6b 0x6d 0x70 0x6c ,0x48 0x48 0x51 0x53 0x53 0x55 0x56 0x57 0x4e ,
0x71 0x71 0x6e 0x6c 0x66 0x65 0x67 0x6c 0x6b ,0x59 0x59 0x55 0x51 0x5e 0x5f 0x5f 0x60 0x5a ,
mid :0x8b 0x8f 0x91 0x90 0x80 0x85 0x87 0x89 0x84 ,0x63 0x62 0x6a 0x6e 0x6c 0x6f 0x70 0x70 0x69 ,
0x8d 0x8d 0x88 0x86 0x80 0x7f 0x81 0x86 0x86 ,0x74 0x74 0x6f 0x6b 0x79 0x79 0x79 0x79 0x74 ,
max :0xa6 0xab 0xab 0xaa 0x9a 0x9f 0xa1 0xa3 0x9d ,0x7e 0x7d 0x83 0x89 0x86 0x8a 0x8b 0x89 0x84 ,
0xa9 0xa9 0xa2 0xa1 0x9a 0x99 0x9b 0xa1 0xa1 ,0x8f 0x8f 0x8a 0x86 0x94 0x94 0x93 0x93 0x8e ,
range:0x35 0x37 0x34 0x34 0x33 0x34 0x34 0x33 0x31 ,0x36 0x35 0x32 0x36 0x33 0x35 0x35 0x32 0x36 ,
0x38 0x38 0x34 0x35 0x34 0x34 0x34 0x35 0x36 ,0x36 0x36 0x35 0x35 0x36 0x35 0x34 0x33 0x34 ,
CA Training result:
cs:0 min :0x3f 0x37 0x40 0x37 0x3f 0x36 0x3f ,0x43 0x3b 0x3f 0x38 0x40 0x39 0x43 ,
cs:0 mid :0x7a 0x79 0x7a 0x77 0x7a 0x78 0x6b ,0x7f 0x7c 0x7b 0x7a 0x7c 0x7a 0x6f ,
cs:0 max :0xb6 0xbb 0xb4 0xb8 0xb5 0xba 0x98 ,0xbb 0xbd 0xb7 0xbc 0xb8 0xbc 0x9b ,
cs:0 range:0x77 0x84 0x74 0x81 0x76 0x84 0x59 ,0x78 0x82 0x78 0x84 0x78 0x83 0x58 ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-gitAUTOINC+4695fbcfba_642a85dd55-tano13 (Jun 09 2023 - 01:42:04)
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
spl: partition error
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(fe4f274c06...) + OK
## Checking uboot 0x00a00000 ... sha256(ce999cc33f...) + OK
## Checking fdt 0x00af9ae8 ... sha256(3fa73a78ba...) + OK
## Checking atf-2 0x00068000 ... sha256(8d44036095...) + OK
## Checking atf-3 0xfdcc9000 ... sha256(990c53fc01...) + OK
## Checking atf-4 0xfdcd0000 ... sha256(e410275b51...) + OK
## Checking atf-5 0x00066000 ... sha256(315a4195a9...) + OK
## Checking optee 0x08400000 ... sha256(b8cddafab0...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 284.331/410.972 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-181-gc9a647cae:cl
NOTICE: BL31: Built : 10:55:41, Oct 18 2021
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: pmu v1 is valid
INFO: dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: Start rockchip platform init
I/TC: Rockchip release version: 1.0
I/TC: OP-TEE version: 3.6.0-307-g0b06ae94 #1 Fri May 7 01:52:27 UTC 2021 aarch64
I/TC: Initialized
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2017.09-gitAUTOINC+4695fbcfba_642a85dd55-tano13 (Jun 09 2023 - 01:42:04 +0000)
Board: FriendlyELEC RK3568 board
PreSerial: 2, raw, 0xfe660000
DRAM: 4 GiB
Sysmem: init
Relocation Offset: ed267000
Relocation fdt: eb9e67c8 - eb9fece0
CR: M/C/I
I2c0 speed: 400000Hz
PMIC: RK8090 (on=0x40, off=0x00)
vdd_logic init 900000 uV
vdd_gpu init 900000 uV
vdd_npu init 900000 uV
io-domain: OK
Failed to get scmi clk dev
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
MMC: switch to partitions #0, OK
mmc1 is current device
Bootdev(atags): mmc 1
MMC1: Legacy, 52Mhz
PartType: EFI
rockchip_set_serialno: could not find efuse/otp device
No misc partition
boot mode: None
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 816000 KHz
dpll 780000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
npll 1200000 KHz
vpll 24000 KHz
hpll 24000 KHz
ppll 200000 KHz
armclk 816000 KHz
aclk_bus 150000 KHz
pclk_bus 100000 KHz
aclk_top_high 300000 KHz
aclk_top_low 200000 KHz
hclk_top 150000 KHz
pclk_top 100000 KHz
aclk_perimid 300000 KHz
hclk_perimid 150000 KHz
pclk_pmu 100000 KHz
No misc partition
vdd_usbc 5157 mV
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'): 2 1 0
switch to partitions #0, OK
mmc1 is current device
MMC read: dev # 1, block # 7936, count 128 ... 128 blocks read: OK
## Executing script at 00c00000
Board name: nanopi5
Loading kernel fitImage...
switch to partitions #0, OK
mmc1 is current device
21999744 bytes read in 1853 ms (11.3 MiB/s)
Force console to be enabled
Booting kernel 0x04080000#conf-rockchip_rk3568-nanopi5-rev02.dtb...
Fdt Ramdisk skip relocation
No misc partition
## Loading kernel from FIT Image at 04080000 ...
Using 'conf-rockchip_rk3568-nanopi5-rev02.dtb' configuration
## Verified-boot: 0
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x0408010c
Data Size: 10941584 Bytes = 10.4 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00280000
Entry Point: 0x00280000
Hash algo: sha256
Hash value: f7c3ab73c0afa95b0a045c6ab557f0b5b87c66b70ae01556fa71e80f3ac7add1
Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at 04080000 ...
Using 'conf-rockchip_rk3568-nanopi5-rev02.dtb' configuration
Trying 'ramdisk-1' ramdisk subimage
Description: twimg-initramfs-swu-factory
Type: RAMDisk Image
Compression: uncompressed
Data Start: 0x04beed1c
Data Size: 10009090 Bytes = 9.5 MiB
Architecture: AArch64
OS: Linux
Load Address: unavailable
Entry Point: unavailable
Hash algo: sha256
Hash value: 213b6a8e1d91cf4703563fae42d26c1a1b67bbd9d7b0dd2ee06931de542ca0e4
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 04080000 ...
Using 'conf-rockchip_rk3568-nanopi5-rev02.dtb' configuration
Trying 'fdt-rockchip_rk3568-nanopi5-rev02.dtb' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x04b1a298
Data Size: 173157 Bytes = 169.1 KiB
Architecture: AArch64
Load Address: 0x0a100000
Hash algo: sha256
Hash value: b58ebecd341b607287ce6ba256c60c44de661cb5d44841934acee749d065cda4
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x04b1a298 to 0x0a100000
Booting using the fdt blob at 0x0a100000
Uncompressing GZIP Kernel Image from 0x0408010c to 0x00280000 ... with 01e72808 bytes OK
kernel loaded at 0x00280000, end = 0x020f2808
Using Device Tree in place at 000000000a100000, end 000000000a12d464
WARNING: could not set reg FDT_ERR_BADOFFSET.
## reserved-memory:
linux,cma: addr=10000000 size=800000
ramoops@110000: addr=110000 size=f0000
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x1f0000000 - 0x200000000 (size: 0x10000000)
== DO RELOCATE == Kernel from 0x00280000 to 0x00200000
Total: 5580.894/5659.739 ms
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux version 6.1.57-tano-rk-standard-gea9e2a9344-tano0.2.1.20.1.0 (oe-user@oe-host) (aarch64-oe-linux-gcc (GCC) 11.4.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP Fri Apr 12 10:45:53 UTC 2024
[ 0.000000] Machine model: FriendlyElec NanoPi R5C
[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-logo@0': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@0': base 0x0000000000000000, size 0 MiB
[ 0.000000] Reserved memory: created CMA memory pool at 0x0000000010000000, size 8 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000200000-0x00000000ffffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal [mem 0x0000000100000000-0x00000001ffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000200000-0x00000000083fffff]
[ 0.000000] node 0: [mem 0x0000000009400000-0x00000000efffffff]
[ 0.000000] node 0: [mem 0x00000001f0000000-0x00000001ffffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[ 0.000000] On node 0, zone DMA: 512 pages in unavailable ranges
[ 0.000000] On node 0, zone DMA: 4096 pages in unavailable ranges
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 26 pages/cpu s68536 r8192 d29768 u106496
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 1286807, 2441009
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1027656
[ 0.000000] Kernel command line: console=ttyFIQ0,1500000n8 earlycon=uart8250,mmio32,0xfe660000 root=/dev/ram rootfstype=squashfs rootwait=1 earlyprintk panic=15 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory coherent_pool=1m swapaccount=1
[ 0.000000] The swapaccount= commandline option is deprecated. Please report your usecase to linux-mm@kvack.org if you depend on this functionality.
[ 0.000000] Unknown kernel command line parameters "earlyprintk rootwait=1 cgroup_enable=memory cgroup_memory=1", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: area num 4.
[ 0.000000] software IO TLB: mapped [mem 0x00000000ec000000-0x00000000f0000000] (64MB)
[ 0.000000] Memory: 3978508K/4175872K available (15552K kernel code, 3338K rwdata, 6032K rodata, 6144K init, 567K bss, 189172K reserved, 8192K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 60789 entries in 238 pages
[ 0.000000] ftrace: allocated 238 pages with 6 groups
[ 0.000000] trace event string verifier disabled
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 320 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[ 0.000000] ITS [mem 0xfd440000-0xfd45ffff]
[ 0.000000] ITS@0x00000000fd440000: allocated 8192 Devices @2400000 (indirect, esz 8, psz 64K, shr 0)
[ 0.000000] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @2410000 (flat, esz 2, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GICv3: using LPI property table @0x0000000002420000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000002430000
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.002853] Console: colour dummy device 80x25
[ 0.003361] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.004362] pid_max: default: 32768 minimum: 301
[ 0.005068] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.005813] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.008142] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.010328] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.011036] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.012051] rcu: Hierarchical SRCU implementation.
[ 0.012522] rcu: Max phase no-delay instances is 1000.
[ 0.014372] Platform MSI: interrupt-controller@fd440000 domain created
[ 0.015700] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[ 0.017828] smp: Bringing up secondary CPUs ...
[ 0.019467] Detected VIPT I-cache on CPU1
[ 0.019596] cacheinfo: Unable to detect cache hierarchy for CPU 1
[ 0.019618] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[ 0.019651] GICv3: CPU1: using allocated LPI pending table @0x0000000002440000
[ 0.019723] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 0.021145] Detected VIPT I-cache on CPU2
[ 0.021265] cacheinfo: Unable to detect cache hierarchy for CPU 2
[ 0.021285] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[ 0.021315] GICv3: CPU2: using allocated LPI pending table @0x0000000002450000
[ 0.021375] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 0.022679] Detected VIPT I-cache on CPU3
[ 0.022791] cacheinfo: Unable to detect cache hierarchy for CPU 3
[ 0.022812] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[ 0.022841] GICv3: CPU3: using allocated LPI pending table @0x0000000002460000
[ 0.022898] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 0.023077] smp: Brought up 1 node, 4 CPUs
[ 0.032435] SMP: Total of 4 processors activated.
[ 0.032898] CPU features: detected: 32-bit EL0 Support
[ 0.033398] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.034228] CPU features: detected: Common not Private translations
[ 0.034854] CPU features: detected: CRC32 instructions
[ 0.035358] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.035914] CPU features: detected: Privileged Access Never
[ 0.036453] CPU features: detected: RAS Extension Support
[ 0.036979] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.037802] CPU: All CPU(s) started at EL2
[ 0.038239] alternatives: applying system-wide alternatives
[ 0.040708] devtmpfs: initialized
[ 0.086285] Registered cp15_barrier emulation handler
[ 0.086812] Registered setend emulation handler
[ 0.087586] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.088589] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.089728] pinctrl core: initialized pinctrl subsystem
[ 0.092124] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.095293] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[ 0.096591] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.097934] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.103787] Registered FIQ tty driver
[ 0.104901] thermal_sys: Registered thermal governor 'fair_share'
[ 0.104916] thermal_sys: Registered thermal governor 'step_wise'
[ 0.105510] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.106206] cpuidle: using governor menu
[ 0.107887] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.108792] ASID allocator initialised with 65536 entries
[ 0.113242] ramoops: dmesg-00x20000@0x0000000000110000
[ 0.113805] ramoops: console0x80000@0x0000000000130000
[ 0.114385] ramoops: pmsg0x50000@0x00000000001b0000
[ 0.115612] printk: console [ramoops-1] enabled
[ 0.116064] pstore: Registered ramoops as persistent store backend
[ 0.116668] ramoops: using 0xf0000@0x110000, ecc: 0
[ 0.147682] platform fe0a0000.hdmi: Fixed dependency cycle(s) with /vop@fe040000/ports/port@0/endpoint@3
[ 0.186822] rockchip-gpio fdd60000.gpio: probed /pinctrl/gpio@fdd60000
[ 0.188467] rockchip-gpio fe740000.gpio: probed /pinctrl/gpio@fe740000
[ 0.190080] rockchip-gpio fe750000.gpio: probed /pinctrl/gpio@fe750000
[ 0.191756] rockchip-gpio fe760000.gpio: probed /pinctrl/gpio@fe760000
[ 0.193358] rockchip-gpio fe770000.gpio: probed /pinctrl/gpio@fe770000
[ 0.194237] rockchip-pinctrl pinctrl: probed pinctrl
[ 0.230941] cryptd: max_cpu_qlen set to 1000
[ 0.234450] fiq_debugger fiq_debugger.0: error -ENXIO: IRQ fiq not found
[ 0.235157] fiq_debugger fiq_debugger.0: error -ENXIO: IRQ wakeup not found
[ 0.235852] fiq_debugger_probe: could not install nmi irq handler
[ 0.236599] printk: console [ttyFIQ0] enabled
[ 0.236599] printk: console [ttyFIQ0] enabled
[ 0.237460] printk: bootconsole [uart8250] disabled
[ 0.237460] printk: bootconsole [uart8250] disabled
[ 0.238343] Registered fiq debugger ttyFIQ0
[ 0.244754] iommu: Default domain type: Translated
[ 0.244790] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.245414] SCSI subsystem initialized
[ 0.245858] usbcore: registered new interface driver usbfs
[ 0.245959] usbcore: registered new interface driver hub
[ 0.246042] usbcore: registered new device driver usb
[ 0.246331] mc: Linux media interface: v0.10
[ 0.246433] videodev: Linux video capture interface: v2.00
[ 0.246635] pps_core: LinuxPPS API ver. 1 registered
[ 0.246661] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.246703] PTP clock support registered
[ 0.247196] arm-scmi firmware:scmi: Enabled polling mode TX channel - prot_id:16
[ 0.247474] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[ 0.247613] arm-scmi firmware:scmi: Malformed reply - real_sz:8 calc_sz:4 (loop_num_ret:3)
[ 0.247645] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 0.249398] Advanced Linux Sound Architecture Driver Initialized.
[ 0.250357] Bluetooth: Core ver 2.22
[ 0.250429] NET: Registered PF_BLUETOOTH protocol family
[ 0.250453] Bluetooth: HCI device and connection manager initialized
[ 0.250483] Bluetooth: HCI socket layer initialized
[ 0.250511] Bluetooth: L2CAP socket layer initialized
[ 0.250556] Bluetooth: SCO socket layer initialized
[ 1.087995] clocksource: Switched to clocksource arch_sys_counter
[ 1.108646] NET: Registered PF_INET protocol family
[ 1.109113] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 1.114705] tcp_listen_portaddr_hash hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 1.114852] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.115004] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 1.115323] TCP bind hash table entries: 32768 (order: 9, 2097152 bytes, linear)
[ 1.117547] TCP: Hash tables configured (established 32768 bind 32768)
[ 1.117827] UDP hash table entries: 2048 (order: 5, 196608 bytes, linear)
[ 1.118168] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes, linear)
[ 1.118779] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.119703] RPC: Registered named UNIX socket transport module.
[ 1.119741] RPC: Registered udp transport module.
[ 1.119759] RPC: Registered tcp transport module.
[ 1.119775] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.121500] PCI: CLS 0 bytes, default 64
[ 1.122783] Trying to unpack rootfs image as initramfs...
[ 1.125449] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available
[ 1.213581] Initialise system trusted keyrings
[ 1.214037] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 1.225966] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.227533] NFS: Registering the id_resolver key type
[ 1.227640] Key type id_resolver registered
[ 1.227664] Key type id_legacy registered
[ 1.227743] ntfs: driver 2.1.32 [Flags: R/O].
[ 1.228113] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 1.228842] fuse: init (API version 7.37)
[ 1.229535] SGI XFS with security attributes, no debug enabled
[ 1.286154] NET: Registered PF_ALG protocol family
[ 1.286231] Key type asymmetric registered
[ 1.286253] Asymmetric key parser 'x509' registered
[ 1.286409] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 1.286439] io scheduler mq-deadline registered
[ 1.286460] io scheduler kyber registered
[ 1.307184] rockchip-snps-pcie3-phy fe8c0000.phy: failed to find rockchip,pipe_grf regmap
[ 1.312533] rk-pcie 3c0000000.pcie: invalid prsnt-gpios property in node
[ 1.312680] rk-pcie 3c0000000.pcie: no vpcie3v3 regulator found
[ 1.313753] rk-pcie 3c0400000.pcie: invalid prsnt-gpios property in node
[ 1.313880] rk-pcie 3c0400000.pcie: no vpcie3v3 regulator found
[ 1.313932] rk-pcie 3c0000000.pcie: host bridge /pcie@fe260000 ranges:
[ 1.314011] rk-pcie 3c0000000.pcie: IO 0x00f4100000..0x00f41fffff -> 0x00f4100000
[ 1.314062] rk-pcie 3c0000000.pcie: MEM 0x00f4200000..0x00f5ffffff -> 0x00f4200000
[ 1.314100] rk-pcie 3c0000000.pcie: MEM 0x0300000000..0x033fffffff -> 0x0300000000
[ 1.314222] rk-pcie 3c0000000.pcie: iATU unroll: enabled
[ 1.314250] rk-pcie 3c0000000.pcie: iATU regions: 8 ob, 8 ib, align 64K, limit 8G
[ 1.314979] rk-pcie 3c0800000.pcie: invalid prsnt-gpios property in node
[ 1.315089] rk-pcie 3c0800000.pcie: no vpcie3v3 regulator found
[ 1.315109] mpp_service mpp-srv: unknown mpp version for missing VCS info
[ 1.315143] mpp_service mpp-srv: probe start
[ 1.321816] mpp_service mpp-srv: probe success
[ 1.323360] snps pcie3phy FW update! size 8192
[ 1.332214] dma-pl330 fe530000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.332286] dma-pl330 fe530000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 1.336866] dma-pl330 fe550000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.336937] dma-pl330 fe550000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 1.338060] rk-pcie 3c0800000.pcie: host bridge /pcie@fe280000 ranges:
[ 1.338159] rk-pcie 3c0800000.pcie: IO 0x00f0100000..0x00f01fffff -> 0x00f0100000
[ 1.338162] rockchip-pvtm fde00000.pvtm: failed to retrieve pvtm_tz
[ 1.338197] rk-pcie 3c0800000.pcie: MEM 0x00f0200000..0x00f1ffffff -> 0x00f0200000
[ 1.338236] rk-pcie 3c0800000.pcie: MEM 0x0380000000..0x03bfffffff -> 0x0380000000
[ 1.338275] rockchip-pvtm fde00000.pvtm: pvtm@0 probed
[ 1.338342] rk-pcie 3c0800000.pcie: iATU unroll: enabled
[ 1.338367] rk-pcie 3c0800000.pcie: iATU regions: 8 ob, 8 ib, align 64K, limit 8G
[ 1.338638] rockchip-pvtm fde80000.pvtm: failed to retrieve pvtm_tz
[ 1.338634] rk-pcie 3c0400000.pcie: host bridge /pcie@fe270000 ranges:
[ 1.338714] rk-pcie 3c0400000.pcie: IO 0x00f2100000..0x00f21fffff -> 0x00f2100000
[ 1.338718] rockchip-pvtm fde80000.pvtm: pvtm@1 probed
[ 1.338748] rk-pcie 3c0400000.pcie: MEM 0x00f2200000..0x00f3ffffff -> 0x00f2200000
[ 1.338786] rk-pcie 3c0400000.pcie: MEM 0x0340000000..0x037fffffff -> 0x0340000000
[ 1.338889] rk-pcie 3c0400000.pcie: iATU unroll: enabled
[ 1.338914] rk-pcie 3c0400000.pcie: iATU regions: 8 ob, 8 ib, align 64K, limit 8G
[ 1.338938] rockchip-pvtm fde90000.pvtm: failed to retrieve pvtm_tz
[ 1.339029] rockchip-pvtm fde90000.pvtm: pvtm@2 probed
[ 1.340035] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 1.341706] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not active.
[ 1.342309] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 1.347313] random: crng init done
[ 1.357672] rockchip-vop2 fe040000.vop: Adding to iommu group 7
[ 1.376293] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0xf, primary plane phy id: 2
[ 1.376383] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x30, primary plane phy id: 4
[ 1.376416] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[ 1.376679] rockchip-vop2 fe040000.vop: [drm:vop2_bind] Esmart1-win0 as cursor plane for vp0
[ 1.376950] rockchip-vop2 fe040000.vop: [drm:vop2_bind] VP2 plane_mask is zero, so ignore register crtc
[ 1.378446] rockchip-vop2 fe040000.vop: bin=0
[ 1.378593] rockchip-vop2 fe040000.vop: Failed to get leakage
[ 1.378783] rockchip-vop2 fe040000.vop: Failed to get reg
[ 1.378991] rockchip-vop2 fe040000.vop: error -ENODEV: _opp_set_regulators: no regulator (vop) found
[ 1.379072] rockchip-vop2 fe040000.vop: failed to set opp config
[ 1.379099] rockchip-vop2 fe040000.vop: failed to init opp info
[ 1.379119] rockchip-vop2 fe040000.vop: failed to init_opp_table
[ 1.379150] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffffc0090303c8)
[ 1.379777] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 1.380869] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[ 1.381255] dwhdmi-rockchip fe0a0000.hdmi: error -ENXIO: IRQ index 1 not found
[ 1.382149] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffffc009043e90)
[ 1.383045] rockchip-drm display-subsystem: failed to parse loader memory
[ 1.384552] [drm] Initialized rockchip 4.0.0 20140818 for display-subsystem on minor 0
[ 1.384869] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[ 1.385219] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[ 1.385866] no ATF memory for init
[ 1.394444] SPI driver panel-simple-spi has no spi_device_id for simple-panel-spi
[ 1.397519] input: hdmi_cec_key as /devices/platform/fe0a0000.hdmi/dw-hdmi-cec.1.auto/input/input0
[ 1.399622] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 1.401017] brd: module loaded
[ 1.410687] loop: module loaded
[ 1.411701] zram: Added device: zram0
[ 1.412241] lkdtm: No crash points registered, enable through debugfs
[ 1.415145] SPI driver spidev has no spi_device_id for rockchip,spidev
[ 1.419564] PPP generic driver version 2.4.2
[ 1.420320] PPP MPPE Compression module registered
[ 1.420381] NET: Registered PF_PPPOX protocol family
[ 1.420819] usbcore: registered new interface driver cdc_ether
[ 1.443056] phy phy-fe8b0000.usb2-phy.3: illegal mode
[ 1.445214] ehci-platform fd800000.usb: EHCI Host Controller
[ 1.445238] phy phy-fe8b0000.usb2-phy.3: illegal mode
[ 1.445308] ohci-platform fd840000.usb: Generic Platform OHCI controller
[ 1.445680] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 2
[ 1.445701] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[ 1.445833] ehci-platform fd880000.usb: EHCI Host Controller
[ 1.445926] ehci-platform fd800000.usb: irq 50, io mem 0xfd800000
[ 1.445966] ohci-platform fd840000.usb: irq 52, io mem 0xfd840000
[ 1.446178] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[ 1.446223] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 3
[ 1.446358] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 1.446407] ehci-platform fd880000.usb: irq 51, io mem 0xfd880000
[ 1.446524] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[ 1.446757] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 5
[ 1.446844] ohci-platform fd8c0000.usb: irq 53, io mem 0xfd8c0000
[ 1.446963] xhci-hcd xhci-hcd.4.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[ 1.447060] xhci-hcd xhci-hcd.4.auto: irq 48, io mem 0xfcc00000
[ 1.447378] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 1.447685] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 6
[ 1.447732] xhci-hcd xhci-hcd.4.auto: Host supports USB 3.0 SuperSpeed
[ 1.448155] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 1.448190] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.448216] usb usb5: Product: xHCI Host Controller
[ 1.448237] usb usb5: Manufacturer: Linux 6.1.57-tano-rk-standard-gea9e2a9344-tano0.2.1.20.1.0 xhci-hcd
[ 1.448258] usb usb5: SerialNumber: xhci-hcd.4.auto
[ 1.449110] hub 5-0:1.0: USB hub found
[ 1.449215] hub 5-0:1.0: 1 port detected
[ 1.450040] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.450341] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 1.450376] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.450402] usb usb6: Product: xHCI Host Controller
[ 1.450423] usb usb6: Manufacturer: Linux 6.1.57-tano-rk-standard-gea9e2a9344-tano0.2.1.20.1.0 xhci-hcd
[ 1.450443] usb usb6: SerialNumber: xhci-hcd.4.auto
[ 1.451264] hub 6-0:1.0: USB hub found
[ 1.451385] hub 6-0:1.0: 1 port detected
[ 1.452418] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 1.452770] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 7
[ 1.453001] xhci-hcd xhci-hcd.5.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[ 1.453112] xhci-hcd xhci-hcd.5.auto: irq 49, io mem 0xfd000000
[ 1.453424] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 1.453710] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 8
[ 1.453755] xhci-hcd xhci-hcd.5.auto: Host supports USB 3.0 SuperSpeed
[ 1.454136] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 1.454172] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.454197] usb usb7: Product: xHCI Host Controller
[ 1.454217] usb usb7: Manufacturer: Linux 6.1.57-tano-rk-standard-gea9e2a9344-tano0.2.1.20.1.0 xhci-hcd
[ 1.454238] usb usb7: SerialNumber: xhci-hcd.5.auto
[ 1.455145] hub 7-0:1.0: USB hub found
[ 1.455241] hub 7-0:1.0: 1 port detected
[ 1.456059] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.456360] usb usb8: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 1.456396] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.456421] usb usb8: Product: xHCI Host Controller
[ 1.456442] usb usb8: Manufacturer: Linux 6.1.57-tano-rk-standard-gea9e2a9344-tano0.2.1.20.1.0 xhci-hcd
[ 1.456464] usb usb8: SerialNumber: xhci-hcd.5.auto
[ 1.457304] hub 8-0:1.0: USB hub found
[ 1.457396] hub 8-0:1.0: 1 port detected
[ 1.458065] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[ 1.458788] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 1.458826] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.458852] usb usb1: Product: EHCI Host Controller
[ 1.458873] usb usb1: Manufacturer: Linux 6.1.57-tano-rk-standard-gea9e2a9344-tano0.2.1.20.1.0 ehci_hcd
[ 1.458895] usb usb1: SerialNumber: fd800000.usb
[ 1.459375] usbcore: registered new interface driver cdc_acm
[ 1.459406] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.459806] hub 1-0:1.0: USB hub found
[ 1.459923] hub 1-0:1.0: 1 port detected
[ 1.459932] usbcore: registered new interface driver uas
[ 1.460165] usbcore: registered new interface driver usb-storage
[ 1.460470] usbcore: registered new interface driver usbserial_generic
[ 1.460533] usbserial: USB Serial support registered for generic
[ 1.460631] usbcore: registered new interface driver ftdi_sio
[ 1.460701] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 1.461118] usbcore: registered new interface driver keyspan
[ 1.461195] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 1.461253] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 1.461380] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 1.461442] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 1.461660] usbcore: registered new interface driver oti6858
[ 1.461725] usbserial: USB Serial support registered for oti6858
[ 1.461831] usbcore: registered new interface driver qcserial
[ 1.461889] usbserial: USB Serial support registered for Qualcomm USB modem
[ 1.466220] i2c_dev: i2c /dev entries driver
[ 1.469670] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected!
[ 1.471398] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[ 1.472015] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 1.472054] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.472078] usb usb3: Product: EHCI Host Controller
[ 1.472099] usb usb3: Manufacturer: Linux 6.1.57-tano-rk-standard-gea9e2a9344-tano0.2.1.20.1.0 ehci_hcd
[ 1.472120] usb usb3: SerialNumber: fd880000.usb
[ 1.473072] hub 3-0:1.0: USB hub found
[ 1.473189] hub 3-0:1.0: 1 port detected
[ 1.473454] i2c 0-0020: Fixed dependency cycle(s) with /i2c@fdd40000/pmic@20/pinctrl_rk8xx/rk817_slppin_rst
[ 1.473512] i2c 0-0020: Fixed dependency cycle(s) with /i2c@fdd40000/pmic@20/pinctrl_rk8xx/rk817_slppin_pwrdn
[ 1.473558] i2c 0-0020: Fixed dependency cycle(s) with /i2c@fdd40000/pmic@20/pinctrl_rk8xx/rk817_slppin_slp
[ 1.475537] rk808 0-0020: chip id: 0x8090
[ 1.475651] rk808 0-0020: No cache defaults, reading back from HW
[ 1.482095] rk808 0-0020: source: on=0x40, off=0x00
[ 1.482148] rk808 0-0020: support dcdc3 fb mode:-22, 167032496
[ 1.482179] rk808 0-0020: support pmic reset mode:0,0
[ 1.490094] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 1.490180] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 1.509170] rk817-battery: Failed to locate of_node [id: -1]
[ 1.509418] rk817-battery rk817-battery: Failed to find matching dt id
[ 1.509626] rk817-charger: Failed to locate of_node [id: -1]
[ 1.509663] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[ 1.509701] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.509726] usb usb2: Product: Generic Platform OHCI controller
[ 1.509748] usb usb2: Manufacturer: Linux 6.1.57-tano-rk-standard-gea9e2a9344-tano0.2.1.20.1.0 ohci_hcd
[ 1.509769] usb usb2: SerialNumber: fd840000.usb
[ 1.509836] rk817-charger rk817-charger: Failed to find matching dt id
[ 1.510719] hub 2-0:1.0: USB hub found
[ 1.510828] hub 2-0:1.0: 1 port detected
[ 1.511799] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input1
[ 1.512015] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[ 1.512055] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.512080] usb usb4: Product: Generic Platform OHCI controller
[ 1.512102] usb usb4: Manufacturer: Linux 6.1.57-tano-rk-standard-gea9e2a9344-tano0.2.1.20.1.0 ohci_hcd
[ 1.512123] usb usb4: SerialNumber: fd8c0000.usb
[ 1.513035] hub 4-0:1.0: USB hub found
[ 1.513153] hub 4-0:1.0: 1 port detected
[ 1.515746] rk808-rtc rk808-rtc: registered as rtc0
[ 1.516400] rk808-rtc rk808-rtc: setting system clock to 2017-08-04T09:00:08 UTC (1501837208)
[ 1.519208] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 1.524298] rtc_hym8563 5-0051: clock/calendar information is no longer guaranteed
[ 1.527280] rtc_hym8563 5-0051: registered as rtc1
[ 1.530817] usbcore: registered new interface driver uvcvideo
[ 1.534313] Bluetooth: HCI UART driver ver 2.3
[ 1.534369] Bluetooth: HCI UART protocol H4 registered
[ 1.534391] Bluetooth: HCI UART protocol ATH3K registered
[ 1.534534] usbcore: registered new interface driver bfusb
[ 1.535333] cpu cpu0: Failed to get specification_serial_number
[ 1.535400] cpu cpu0: Failed to get leakage
[ 1.536244] cpu cpu0: soc version=0, speed=0
[ 1.539055] cpu cpu0: avs=0
[ 1.539397] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=1416000000 h_limit=0 h_table=0
[ 1.541262] cpu cpu0: EM: created perf domain
[ 1.542911] sdhci: Secure Digital Host Controller Interface driver
[ 1.542953] sdhci: Copyright(c) Pierre Ossman
[ 1.542973] Synopsys Designware Multimedia Card Interface Driver
[ 1.543656] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.544357] dwmmc_rockchip fe2b0000.mmc: No normal pinctrl state
[ 1.544388] dwmmc_rockchip fe2b0000.mmc: No idle pinctrl state
[ 1.544906] dwmmc_rockchip fe2b0000.mmc: IDMAC supports 32-bit address mode.
[ 1.546855] dwmmc_rockchip fe2b0000.mmc: Using internal DMA controller.
[ 1.546896] dwmmc_rockchip fe2b0000.mmc: Version ID is 270a
[ 1.546982] dwmmc_rockchip fe2b0000.mmc: DW MMC controller at irq 83,32 bit host data width,256 deep fifo
[ 1.547578] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.547643] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[ 1.547744] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 1.548047] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 1.548619] rk-crypto fe380000.crypto: invalid resource
[ 1.550116] rk-crypto fe380000.crypto: CRYPTO V2.0.0.0 Accelerator successfully registered
[ 1.550532] hid: raw HID events driver (C) Jiri Kosina
[ 1.551038] usbcore: registered new interface driver usbhid
[ 1.551058] usbhid: USB HID core driver
[ 1.551803] rockchip,bus bus-npu: bin=0
[ 1.551851] rockchip,bus bus-npu: Failed to get leakage
[ 1.553248] rockchip,bus bus-npu: avs=0
[ 1.557230] optee: probing for conduit method.
[ 1.557294] optee: revision 3.6 (0b06ae94)
[ 1.557828] optee: initialized driver
[ 1.559583] usbcore: registered new interface driver snd-usb-audio
[ 1.561072] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 1.562183] rk817-codec rk817-codec: DMA mask not set
[ 1.568795] NET: Registered PF_LLC protocol family
[ 1.568857] u32 classifier
[ 1.568868] input device check on
[ 1.568876] Actions configured
[ 1.568970] Initializing XFRM netlink socket
[ 1.569394] NET: Registered PF_INET6 protocol family
[ 1.570477] Segment Routing with IPv6
[ 1.570533] In-situ OAM (IOAM) with IPv6
[ 1.570601] NET: Registered PF_PACKET protocol family
[ 1.570626] NET: Registered PF_KEY protocol family
[ 1.570763] Bridge firewalling registered
[ 1.571026] Bluetooth: RFCOMM socket layer initialized
[ 1.571078] Bluetooth: RFCOMM ver 1.11
[ 1.571100] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.571118] Bluetooth: HIDP socket layer initialized
[ 1.571189] l2tp_core: L2TP core driver, V2.0
[ 1.571211] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.571222] l2tp_netlink: L2TP netlink interface
[ 1.571289] 8021q: 802.1Q VLAN Support v1.8
[ 1.571409] [BT_RFKILL]: Enter rfkill_rk_init
[ 1.571423] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 1.572449] Key type dns_resolver registered
[ 1.573795] Loading compiled-in X.509 certificates
[ 1.574724] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 1.576720] pstore: Using crash dump compression: deflate
[ 1.578030] mmc0: SDHCI controller on fe310000.mmc [fe310000.mmc] using ADMA
[ 1.590774] rga2: Driver loaded successfully ver:3.2.63318
[ 1.591116] rga2: Module initialized.
[ 1.601404] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 1.604763] rk-pcie 3c0400000.pcie: PCIe Link up, LTSSM is 0x130011
[ 1.604815] rk-pcie 3c0800000.pcie: PCIe Link up, LTSSM is 0x130011
[ 1.604824] rk-pcie 3c0400000.pcie: PCIe Gen.2 x1 link up
[ 1.604833] rk-pcie 3c0800000.pcie: PCIe Gen.2 x1 link up
[ 1.605053] rk-pcie 3c0800000.pcie: PCI host bridge to bus 0002:20
[ 1.605054] rk-pcie 3c0400000.pcie: PCI host bridge to bus 0001:10
[ 1.605065] pci_bus 0001:10: root bus resource [bus 10-1f]
[ 1.605074] pci_bus 0001:10: root bus resource [io 0x200000-0x2fffff] (bus address [0xf2100000-0xf21fffff])
[ 1.605079] pci_bus 0002:20: root bus resource [bus 20-2f]
[ 1.605087] pci_bus 0001:10: root bus resource [mem 0xf2200000-0xf3ffffff]
[ 1.605094] pci_bus 0002:20: root bus resource [io 0x100000-0x1fffff] (bus address [0xf0100000-0xf01fffff])
[ 1.605100] pci_bus 0001:10: root bus resource [mem 0x340000000-0x37fffffff]
[ 1.605111] pci_bus 0002:20: root bus resource [mem 0xf0200000-0xf1ffffff]
[ 1.605123] pci_bus 0002:20: root bus resource [mem 0x380000000-0x3bfffffff]
[ 1.605136] pci 0001:10:00.0: [1d87:3566] type 01 class 0x060400
[ 1.605153] pci 0002:20:00.0: [1d87:3566] type 01 class 0x060400
[ 1.605167] pci 0001:10:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[ 1.605173] pci 0002:20:00.0: reg 0x10: [mem 0x00000000-0x3fffffff]
[ 1.605191] pci 0002:20:00.0: reg 0x14: [mem 0x00000000-0x3fffffff]
[ 1.605207] pci 0002:20:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[ 1.605247] pci 0001:10:00.0: supports D1 D2
[ 1.605258] pci 0001:10:00.0: PME# supported from D0 D1 D3hot
[ 1.605273] pci 0002:20:00.0: supports D1 D2
[ 1.605284] pci 0002:20:00.0: PME# supported from D0 D1 D3hot
[ 1.622429] rockchip-iodomain fdc20000.syscon:io-domains: pmuio2(3300000 uV) supplied by vcc3v3_pmu
[ 1.623164] rockchip-iodomain fdc20000.syscon:io-domains: vccio1(3300000 uV) supplied by vccio_acodec
[ 1.624094] rockchip-iodomain fdc20000.syscon:io-domains: vccio3(3300000 uV) supplied by vccio_sd
[ 1.624769] rockchip-iodomain fdc20000.syscon:io-domains: vccio4(1800000 uV) supplied by vcc_1v8
[ 1.625535] rockchip-iodomain fdc20000.syscon:io-domains: vccio5(3300000 uV) supplied by vcc_3v3
[ 1.625894] rockchip-iodomain fdc20000.syscon:io-domains: vccio6(1800000 uV) supplied by vcc_1v8
[ 1.626240] rockchip-iodomain fdc20000.syscon:io-domains: vccio7(3300000 uV) supplied by vcc_3v3
[ 1.627195] pci 0002:20:00.0: Primary bus is hard wired to 0
[ 1.627233] pci 0002:20:00.0: bridge configuration invalid ([bus 01-ff]), reconfiguring
[ 1.627910] pci 0001:10:00.0: Primary bus is hard wired to 0
[ 1.627939] pci 0001:10:00.0: bridge configuration invalid ([bus 01-ff]), reconfiguring
[ 1.628030] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 1.628054] pci 0002:21:00.0: [10ec:8125] type 00 class 0x020000
[ 1.628126] pci 0002:21:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 1.628203] pci 0002:21:00.0: reg 0x18: [mem 0x00000000-0x0000ffff 64bit]
[ 1.628255] pci 0002:21:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit]
[ 1.628363] mpp_rkvenc fdf40000.rkvenc: Adding to iommu group 5
[ 1.628386] pci 0001:11:00.0: [10ec:8125] type 00 class 0x020000
[ 1.628487] pci 0001:11:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 1.628610] mpp_rkvenc fdf40000.rkvenc: probing start
[ 1.628643] pci 0001:11:00.0: reg 0x18: [mem 0x00000000-0x0000ffff 64bit]
[ 1.628730] pci 0001:11:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit]
[ 1.628917] pci 0002:21:00.0: supports D1 D2
[ 1.628928] pci 0002:21:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.629120] mpp_rkvenc fdf40000.rkvenc: bin=0
[ 1.629150] mpp_rkvenc fdf40000.rkvenc: Failed to get leakage
[ 1.629280] debugfs: Directory 'fdf40000.rkvenc-venc' with parent 'vdd_logic' already present!
[ 1.629403] pci 0001:11:00.0: supports D1 D2
[ 1.629415] pci 0001:11:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.629509] mpp_rkvenc fdf40000.rkvenc: avs=0
[ 1.629708] mpp_rkvenc fdf40000.rkvenc: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[ 1.630210] mpp_rkvenc fdf40000.rkvenc: probing finish
[ 1.630655] mpp_vdpu2 fdea0400.vdpu: Adding to iommu group 1
[ 1.630856] mpp_vdpu2 fdea0400.vdpu: probe device
[ 1.631500] mpp_vdpu2 fdea0400.vdpu: probing finish
[ 1.632033] mpp_vepu2 fdee0000.vepu: Adding to iommu group 3
[ 1.632296] mpp_vepu2 fdee0000.vepu: probing start
[ 1.632864] mpp_vepu2 fdee0000.vepu: probing finish
[ 1.633431] mpp-iep2 fdef0000.iep: Adding to iommu group 4
[ 1.633637] mpp-iep2 fdef0000.iep: probe device
[ 1.633997] mpp-iep2 fdef0000.iep: allocate roi buffer failed
[ 1.634211] mpp-iep2 fdef0000.iep: probing finish
[ 1.634617] mpp_jpgdec fded0000.jpegd: Adding to iommu group 2
[ 1.635376] mpp_jpgdec fded0000.jpegd: probe device
[ 1.635952] mpp_jpgdec fded0000.jpegd: probing finish
[ 1.636540] mpp_rkvdec2 fdf80200.rkvdec: Adding to iommu group 6
[ 1.636916] mpp_rkvdec2 fdf80200.rkvdec: rkvdec, probing start
[ 1.637340] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found!
[ 1.637356] rkvdec2_init:1197: No niu aclk reset resource define
[ 1.637368] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found!
[ 1.637376] rkvdec2_init:1200: No niu hclk reset resource define
[ 1.637681] mpp_rkvdec2 fdf80200.rkvdec: bin=0
[ 1.637716] mpp_rkvdec2 fdf80200.rkvdec: Failed to get leakage
[ 1.637852] debugfs: Directory 'fdf80200.rkvdec-vdec' with parent 'vdd_logic' already present!
[ 1.638078] pci_bus 0002:21: busn_res: [bus 21-2f] end is updated to 21
[ 1.638210] mpp_rkvdec2 fdf80200.rkvdec: avs=0
[ 1.638415] mpp_rkvdec2 fdf80200.rkvdec: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[ 1.638561] pci 0002:20:00.0: BAR 0: no space for [mem size 0x40000000]
[ 1.638577] pci 0002:20:00.0: BAR 0: failed to assign [mem size 0x40000000]
[ 1.638591] pci 0002:20:00.0: BAR 1: no space for [mem size 0x40000000]
[ 1.638601] pci 0002:20:00.0: BAR 1: failed to assign [mem size 0x40000000]
[ 1.638613] pci 0002:20:00.0: BAR 8: assigned [mem 0xf0200000-0xf02fffff]
[ 1.638624] pci 0002:20:00.0: BAR 6: assigned [mem 0xf0300000-0xf030ffff pref]
[ 1.638636] pci 0002:20:00.0: BAR 7: assigned [io 0x100000-0x100fff]
[ 1.638656] pci 0002:21:00.0: BAR 2: assigned [mem 0xf0200000-0xf020ffff 64bit]
[ 1.638666] mpp_rkvdec2 fdf80200.rkvdec: sram_start 0x00000000fdcc0000
[ 1.638679] mpp_rkvdec2 fdf80200.rkvdec: rcb_iova 0x0000000010000000
[ 1.638688] mpp_rkvdec2 fdf80200.rkvdec: sram_size 45056
[ 1.638697] mpp_rkvdec2 fdf80200.rkvdec: rcb_size 65536
[ 1.638702] pci 0002:21:00.0: BAR 4: assigned [mem 0xf0210000-0xf0213fff 64bit]
[ 1.638706] mpp_rkvdec2 fdf80200.rkvdec: min_width 512
[ 1.638751] pci 0002:21:00.0: BAR 0: assigned [io 0x100000-0x1000ff]
[ 1.638767] mpp_rkvdec2 fdf80200.rkvdec: link mode probe finish
[ 1.638772] pci 0002:20:00.0: PCI bridge to [bus 21]
[ 1.638784] pci 0002:20:00.0: bridge window [io 0x100000-0x100fff]
[ 1.638795] pci 0002:20:00.0: bridge window [mem 0xf0200000-0xf02fffff]
[ 1.638845] mpp_rkvdec2 fdf80200.rkvdec: probing finish
[ 1.638856] mpp_rkvdec2 fdf80200.rkvdec: probing finish
[ 1.640172] mali fde60000.gpu: Kernel DDK version g21p0-01eac0
[ 1.640583] mali fde60000.gpu: GPU metrics tracepoint support enabled
[ 1.641032] mali fde60000.gpu: Failed to get specification_serial_number
[ 1.641078] mali fde60000.gpu: Failed to get leakage
[ 1.641167] mali fde60000.gpu: soc version=0, speed=0
[ 1.641258] debugfs: Directory 'fde60000.gpu-mali' with parent 'vdd_gpu' already present!
[ 1.641784] pcieport 0002:20:00.0: PME: Signaling with IRQ 103
[ 1.641800] debugfs: File 'Capture' in directory 'dapm' already present!
[ 1.642268] mali fde60000.gpu: avs=0
[ 1.642300] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 144; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 1.642561] mali fde60000.gpu: Register LUT 00070200 initialized for GPU arch 0x00070400
[ 1.642603] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
[ 1.642791] mali fde60000.gpu: No priority control manager is configured
[ 1.642805] mali fde60000.gpu: Large page support was disabled at compile-time!
[ 1.642927] mali fde60000.gpu: No memory group manager is configured
[ 1.644219] pcieport 0002:20:00.0: AER: enabled with IRQ 104
[ 1.644300] mali fde60000.gpu: l=0 h=2147483647 hyst=5000 l_limit=700000000 h_limit=0 h_table=0
[ 1.644865] input: gpio-keys as /devices/platform/gpio-keys/input/input2
[ 1.644981] mali fde60000.gpu: Couldn't find power_model DT node matching 'arm,mali-simple-power-model'
[ 1.645001] mali fde60000.gpu: Error -22, no DT entry: mali-simple-power-model.static-coefficient = 1*[0]
[ 1.645612] mali fde60000.gpu: Error -22, no DT entry: mali-simple-power-model.dynamic-coefficient = 1*[0]
[ 1.645927] mali fde60000.gpu: Error -22, no DT entry: mali-simple-power-model.ts = 4*[0]
[ 1.646199] mali fde60000.gpu: Error -22, no DT entry: mali-simple-power-model.thermal-zone = ''
[ 1.648695] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 1.648877] mali fde60000.gpu: Using configured power model mali-g52_r1-power-model, and fallback mali-simple-power-model
[ 1.649655] mali fde60000.gpu: * MALI kbase_mmap_min_addr compiled to CONFIG_DEFAULT_MMAP_MIN_ADDR, no runtime update possible! *
[ 1.649685] mali fde60000.gpu: Probed as mali0
[ 1.651423] pci_bus 0001:11: busn_res: [bus 11-1f] end is updated to 11
[ 1.651478] pci 0001:10:00.0: BAR 8: assigned [mem 0xf2200000-0xf22fffff]
[ 1.651493] pci 0001:10:00.0: BAR 6: assigned [mem 0xf2300000-0xf230ffff pref]
[ 1.651505] pci 0001:10:00.0: BAR 7: assigned [io 0x200000-0x200fff]
[ 1.651522] pci 0001:11:00.0: BAR 2: assigned [mem 0xf2200000-0xf220ffff 64bit]
[ 1.651567] pci 0001:11:00.0: BAR 4: assigned [mem 0xf2210000-0xf2213fff 64bit]
[ 1.651609] pci 0001:11:00.0: BAR 0: assigned [io 0x200000-0x2000ff]
[ 1.651632] pci 0001:10:00.0: PCI bridge to [bus 11]
[ 1.651642] pci 0001:10:00.0: bridge window [io 0x200000-0x200fff]
[ 1.651654] pci 0001:10:00.0: bridge window [mem 0xf2200000-0xf22fffff]
[ 1.654237] pcieport 0001:10:00.0: PME: Signaling with IRQ 115
[ 1.654666] pcieport 0001:10:00.0: AER: enabled with IRQ 116
[ 1.654772] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 100000000Hz, actual 50000000HZ div = 0)
[ 1.654864] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 1.668306] dwmmc_rockchip fe2b0000.mmc: Successfully tuned phase to 270
[ 1.668356] mmc1: new ultra high speed SDR50 SDHC card at address aaaa
[ 1.669233] mmcblk1: mmc1:aaaa SL16G 14.8 GiB
[ 1.670115] mmc0: Host Software Queue enabled
[ 1.670150] mmc0: new HS200 MMC card at address 0001
[ 1.670820] mmcblk0: mmc0:0001 A3A551 28.9 GiB
[ 1.672592] mmcblk0boot0: mmc0:0001 A3A551 4.00 MiB
[ 1.673907] mmcblk0boot1: mmc0:0001 A3A551 4.00 MiB
[ 1.675091] mmcblk0rpmb: mmc0:0001 A3A551 16.0 MiB, chardev (237:0)
[ 1.677819] mmcblk1: p1 p2 p3
[ 1.684677] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 1.711392] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 1.717655] Freeing initrd memory: 9772K
[ 1.726680] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 1.727356] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 1.727381] cfg80211: failed to load regulatory.db
[ 1.727712] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 1.728183] rockchip-suspend not set sleep-mode-config for mem-lite
[ 1.728196] rockchip-suspend not set wakeup-config for mem-lite
[ 1.728205] rockchip-suspend not set sleep-mode-config for mem-ultra
[ 1.728213] rockchip-suspend not set wakeup-config for mem-ultra
[ 1.728969] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 407; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '10:45:53', on 'Apr 12 2024'.
[ 1.729340] Mali:
[ 1.729345] Mali device driver loaded
[ 1.729361] ALSA device list:
[ 1.729368] #0: rockchip,hdmi0
[ 1.733705] Freeing unused kernel memory: 6144K
[ 1.738001] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 1.748037] Run /init as init process
[ 1.768044] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.058346] init: Console is alive
[ 2.058547] init: - watchdog -
[ 2.061438] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.061533] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.069193] init: - preinit -
Press the [x] key to cancel automatic installation
Press the [r] key to install without last action (reboot/power off)
[ 4.208125] rk-pcie 3c0000000.pcie: PCIe Link Fail, LTSSM is 0x3, hw_retries=0
┌────────────────────────┐
│ │
│ Global configuration │
│ │
└────────────────────────┘
* Last action: reboot
* Last action delay: 5 seconds
┌────────────────┐
│ │
│ Verification │
│ │
└────────────────┘
Checking required block devices...
════════════════════════════════════════════════════════════════════════════════
Block device /dev/mmcblk0 found
Block device /dev/mmcblk1 found
┌────────────────────┐
│ │
│ Pre-installation │
│ │
└────────────────────┘
Mounting filesystems...
════════════════════════════════════════════════════════════════════════════════
Mount 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk1p3
* Target: /mnt
* Filsystem: vfat
* Create target: yes
Executing command '/bin/mount -t vfat /dev/mmcblk1p3 /mnt'...
Executed '/bin/mount -t vfat /dev/mmcblk1p3 /mnt' with exit code 0
Mounted
Erasing block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0
* Block size: 512
* Count: 131072
Executing command '/bin/dd if=/dev/zero of=/dev/mmcblk0 bs=512 count=131072'...
131072+0 records in
131072+0 records out
Executed '/bin/dd if=/dev/zero of=/dev/mmcblk0 bs=512 count=131072' with exit code 0
Block device /dev/mmcblk0 erased
Creating partitions on block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0
* Label: gpt
* Block device size: 31037849600
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mklabel gpt'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mklabel gpt' with exit code 0
Executing command '/usr/sbin/partprobe'...
Executed '/usr/sbin/partprobe' with exit code 0
Partition 1:
* Name: boot
* Partition type: primary
* Start: 8MiB
* End: 16MiB
* UUID: 3309c654-a79f-4104-97d4-5b6c5d1710b0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 8MiB 16MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 8MiB 16MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 1 'boot''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 1 'boot'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=1:3309c654-a79f-4104-97d4-5b6c5d1710b0 /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=1:3309c654-a79f-4104-97d4-5b6c5d1710b0 /dev/mmcblk0' with exit code 0
Partition 2:
* Name: kernel_a
* Partition type: primary
* Filesystem type: ext4
* Start: 16MiB
* End: 80MiB
* UUID: a3d2fa83-cb5e-40bf-95b1-18b315afc493
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 16MiB 80MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 16MiB 80MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 2 'kernel_a''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 2 'kernel_a'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=2:a3d2fa83-cb5e-40bf-95b1-18b315afc493 /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=2:a3d2fa83-cb5e-40bf-95b1-18b315afc493 /dev/mmcblk0' with exit code 0
Partition 3:
* Name: rootfs_a
* Partition type: primary
* Start: 80MiB
* End: 4176MiB
* UUID: 0a746ef1-a4b5-417e-bede-019acb00c93c
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 80MiB 4176MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 80MiB 4176MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 3 'rootfs_a''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 3 'rootfs_a'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=3:0a746ef1-a4b5-417e-bede-019acb00c93c /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=3:0a746ef1-a4b5-417e-bede-019acb00c93c /dev/mmcblk0' with exit code 0
Partition 4:
* Name: kernel_b
* Partition type: primary
* Filesystem type: ext4
* Start: 4176MiB
* End: 4240MiB
* UUID: 63b18e7b-e350-465b-af6b-4e33630d8957
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 4176MiB 4240MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 4176MiB 4240MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 4 'kernel_b''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 4 'kernel_b'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=4:63b18e7b-e350-465b-af6b-4e33630d8957 /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=4:63b18e7b-e350-465b-af6b-4e33630d8957 /dev/mmcblk0' with exit code 0
Partition 5:
* Name: rootfs_b
* Partition type: primary
* Start: 4240MiB
* End: 8336MiB
* UUID: bcd0b8b4-18ff-4e92-98e4-bd37e2d8a09c
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 4240MiB 8336MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 4240MiB 8336MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 5 'rootfs_b''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 5 'rootfs_b'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=5:bcd0b8b4-18ff-4e92-98e4-bd37e2d8a09c /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=5:bcd0b8b4-18ff-4e92-98e4-bd37e2d8a09c /dev/mmcblk0' with exit code 0
Partition 6:
* Name: rootfs_data
* Partition type: primary
* Filesystem type: ext4
* Start: 8336MiB
* End: 100%
* UUID: 123f16b0-7340-43a6-b9cd-4eb847e21c42
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 8336MiB 100%'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 8336MiB 100%' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 6 'rootfs_data''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 6 'rootfs_data'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=6:123f16b0-7340-43a6-b9cd-4eb847e21c42 /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=6:123f16b0-7340-43a6-b9cd-4eb847e21c42 /dev/mmcblk0' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script print'...
Model: MMC A3A551 (sd/mmc)
Disk /dev/mmcblk0: 31.0GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:
Number Start End Size File system Name Flags
1 8389kB 16.8MB 8389kB boot
2 16.8MB 83.9MB 67.1MB kernel_a
3 83.9MB 4379MB 4295MB rootfs_a
4 4379MB 4446MB 67.1MB kernel_b
5 4446MB 8741MB 4295MB rootfs_b
6 8741MB 31.0GB 22.3GB rootfs_data
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script print' with exit code 0
Executing command '/usr/sbin/partprobe'...
Executed '/usr/sbin/partprobe' with exit code 0
Created partitions on block device /dev/mmcblk0
Creating filesystems on block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0p6
* Filesystem type: ext4
* Label: rootfs_data
Executing command '/sbin/mkfs.ext4 -F -L rootfs_data /dev/mmcblk0p6'...
mke2fs 1.46.5 (30-Dec-2021)
Discarding device blocks: done
Creating filesystem with 5443328 4k blocks and 1362720 inodes
Filesystem UUID: 198c7c98-9df8-4068-a82e-240ab05ad177
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
4096000
Allocating group tables: done
Writing inode tables: done
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information: done
Executed '/sbin/mkfs.ext4 -F -L rootfs_data /dev/mmcblk0p6' with exit code 0
Created ext4 filesystem on /dev/mmcblk0p6
Writing images to block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0
Image 1:
* Image source: local
* Image URL: /mnt/u-boot-initial-env.bin
* Offset: 4128768 bytes
Executing command '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=4128768 seek=1'...
0+1 records in
0+1 records out
Executed '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=4128768 seek=1' with exit code 0
Image 2:
* Image source: local
* Image URL: /mnt/u-boot-initial-env.bin
* Offset: 4161536 bytes
Executing command '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=4161536 seek=1'...
0+1 records in
0+1 records out
Executed '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=4161536 seek=1' with exit code 0
Writed images to block device /dev/mmcblk0
┌────────────────┐
│ │
│ Installation │
│ │
└────────────────┘
┌─────────────────────┐
│ │
│ Installing images │
│ │
└─────────────────────┘
Installing image 1...
════════════════════════════════════════════════════════════════════════════════
* Type: swupdate
* Image source: local
* Image URL: /mnt/swu_install.swu
* Extra arguments: --no-bootloader-env
* Dry run: 1
* Install: 1
* Selections: ${SWU_SYSTEM_A_SELECTION} ${SWU_SYSTEM_B_SELECTION}
* Selections (expanded): tanowrt,system-a tanowrt,system-b
[dry] run for selection 'tanowrt,system-a'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.8.rk0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on nanopi-r5c-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-a
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 3974
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2024-05-16-00:07:13-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for FriendlyElec NanoPi R5C (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_a 2024-05-16-00:07:13-UTC: twimg-default-nanopi-r5c-emmc.squashfs-lzo in device : /dev/mmcblk0p3 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_a 6.1.57+gitAUTOINC+ea9e2a9344-tano0.2.1.20.1.0: fitImage-nanopi-r5c-emmc.ext4 in device : /dev/mmcblk0p2 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.rk0: startup-nanopi-r5c-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2017.09-gitAUTOINC+4695fbcfba_642a85dd55-tano13: u-boot-nanopi-r5c-emmc.bin-emmc in device : /dev/mmcblk0p1 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image idblock fe07abc05b388eaf106cff71f6b88c9f: idblock.img-nanopi-r5c-emmc-emmc in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 0
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware nanopi-r5c-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename twimg-default-nanopi-r5c-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 48812032
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM twimg-default-nanopi-r5c-emmc.squashfs-lzo, 48812032 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream twimg-default-nanopi-r5c-emmc.squashfs-lzo dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename idblock.img-nanopi-r5c-emmc-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 262144
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-nanopi-r5c-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 2097152
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-nanopi-r5c-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2306
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-nanopi-r5c-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 15436800
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-nanopi-r5c-emmc.ext4, 15436800 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-nanopi-r5c-emmc.ext4 dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream idblock.img-nanopi-r5c-emmc-emmc dummy
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 32768 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-nanopi-r5c-emmc.bin-emmc dummy
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-nanopi-r5c-emmc.img dummy
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 4063232 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-a' [dry] run success
[dry] run for selection 'tanowrt,system-b'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.8.rk0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on nanopi-r5c-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-b
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 3974
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2024-05-16-00:07:13-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for FriendlyElec NanoPi R5C (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_b 2024-05-16-00:07:13-UTC: twimg-default-nanopi-r5c-emmc.squashfs-lzo in device : /dev/mmcblk0p5 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_b 6.1.57+gitAUTOINC+ea9e2a9344-tano0.2.1.20.1.0: fitImage-nanopi-r5c-emmc.ext4 in device : /dev/mmcblk0p4 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.rk0: startup-nanopi-r5c-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2017.09-gitAUTOINC+4695fbcfba_642a85dd55-tano13: u-boot-nanopi-r5c-emmc.bin-emmc in device : /dev/mmcblk0p1 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image idblock fe07abc05b388eaf106cff71f6b88c9f: idblock.img-nanopi-r5c-emmc-emmc in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 1
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware nanopi-r5c-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename twimg-default-nanopi-r5c-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 48812032
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM twimg-default-nanopi-r5c-emmc.squashfs-lzo, 48812032 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream twimg-default-nanopi-r5c-emmc.squashfs-lzo dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename idblock.img-nanopi-r5c-emmc-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 262144
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-nanopi-r5c-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 2097152
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-nanopi-r5c-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2306
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-nanopi-r5c-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 15436800
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-nanopi-r5c-emmc.ext4, 15436800 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-nanopi-r5c-emmc.ext4 dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream idblock.img-nanopi-r5c-emmc-emmc dummy
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 32768 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-nanopi-r5c-emmc.bin-emmc dummy
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-nanopi-r5c-emmc.img dummy
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 4063232 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-b' [dry] run success
[install] run for selection 'tanowrt,system-a'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.8.rk0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on nanopi-r5c-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-a
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 3974
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2024-05-16-00:07:13-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for FriendlyElec NanoPi R5C (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_a 2024-05-16-00:07:13-UTC: twimg-default-nanopi-r5c-emmc.squashfs-lzo in device : /dev/mmcblk0p3 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_a 6.1.57+gitAUTOINC+ea9e2a9344-tano0.2.1.20.1.0: fitImage-nanopi-r5c-emmc.ext4 in device : /dev/mmcblk0p2 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.rk0: startup-nanopi-r5c-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2017.09-gitAUTOINC+4695fbcfba_642a85dd55-tano13: u-boot-nanopi-r5c-emmc.bin-emmc in device : /dev/mmcblk0p1 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image idblock fe07abc05b388eaf106cff71f6b88c9f: idblock.img-nanopi-r5c-emmc-emmc in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 0
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware nanopi-r5c-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh preupdate tanowrt system-a command returned 0
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename twimg-default-nanopi-r5c-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 48812032
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM twimg-default-nanopi-r5c-emmc.squashfs-lzo, 48812032 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream twimg-default-nanopi-r5c-emmc.squashfs-lzo raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename idblock.img-nanopi-r5c-emmc-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 262144
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-nanopi-r5c-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 2097152
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-nanopi-r5c-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2306
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-nanopi-r5c-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 15436800
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-nanopi-r5c-emmc.ext4, 15436800 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-nanopi-r5c-emmc.ext4 raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream idblock.img-nanopi-r5c-emmc-emmc raw
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 32768 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-nanopi-r5c-emmc.bin-emmc raw
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-nanopi-r5c-emmc.img raw
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 4063232 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh postupdate-success tanowrt system-a command returned 0
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-a' [install] run success
[install] run for selection 'tanowrt,system-b'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.8.rk0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on nanopi-r5c-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-b
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE][TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
: SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 3974
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2024-05-16-00:07:13-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for FriendlyElec NanoPi R5C (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_b 2024-05-16-00:07:13-UTC: twimg-default-nanopi-r5c-emmc.squashfs-lzo in device : /dev/mmcblk0p5 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_b 6.1.57+gitAUTOINC+ea9e2a9344-tano0.2.1.20.1.0: fitImage-nanopi-r5c-emmc.ext4 in device : /dev/mmcblk0p4 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.rk0: startup-nanopi-r5c-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2017.09-gitAUTOINC+4695fbcfba_642a85dd55-tano13: u-boot-nanopi-r5c-emmc.bin-emmc in device : /dev/mmcblk0p1 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image idblock fe07abc05b388eaf106cff71f6b88c9f: idblock.img-nanopi-r5c-emmc-emmc in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 1
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware nanopi-r5c-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh preupdate tanowrt system-b command returned 0
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename twimg-default-nanopi-r5c-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 48812032
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM twimg-default-nanopi-r5c-emmc.squashfs-lzo, 48812032 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream twimg-default-nanopi-r5c-emmc.squashfs-lzo raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename idblock.img-nanopi-r5c-emmc-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 262144
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-nanopi-r5c-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 2097152
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-nanopi-r5c-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2306
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-nanopi-r5c-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 15436800
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-nanopi-r5c-emmc.ext4, 15436800 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-nanopi-r5c-emmc.ext4 raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream idblock.img-nanopi-r5c-emmc-emmc raw
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 32768 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-nanopi-r5c-emmc.bin-emmc raw
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-nanopi-r5c-emmc.img raw
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 4063232 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh postupdate-success tanowrt system-b command returned 0
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-b' [install] run success
┌─────────────────────┐
│ │
│ Post-installation │
│ │
└─────────────────────┘
Executing custom commands...
════════════════════════════════════════════════════════════════════════════════
Command 1
────────────────────────────────────────────────────────────
* Command: fw_setenv swu_active 0
* Required exit code : 0
Executing command 'fw_setenv swu_active 0'...
Executed 'fw_setenv swu_active 0' with exit code 0
Command 2
────────────────────────────────────────────────────────────
* Command: fw_setenv swu_upgrade_available 0
* Required exit code : 0
Executing command 'fw_setenv swu_upgrade_available 0'...
Executed 'fw_setenv swu_upgrade_available 0' with exit code 0
Command 3
────────────────────────────────────────────────────────────
* Command: fw_setenv swu_bootcount 0
* Required exit code : 0
Executing command 'fw_setenv swu_bootcount 0'...
Executed 'fw_setenv swu_bootcount 0' with exit code 0
┌────────────────────────────────────────────────┐
│ │
│ SUCCESS: Installation successfully completed │
│ │
└────────────────────────────────────────────────┘
Rebooting in 5 seconds...
Rebooting in 4 seconds...
Rebooting in 3 seconds...
Rebooting in 2 seconds...
Rebooting in 1 seconds...
Rebooting now...
[ 35.241752] reboot: Restarting system