3.12.2 Microchip EVB-KSZ9477 Booting from Internal NAND Flash Logs
3.12.2.1 AT91Bootstrap
AT91Bootstrap 4.0.8-gitAUTOINC+c331a16179-r0.tano3.3 (2023-12-18 09:57:32)
NAND: ONFI flash detected
NAND: Manufacturer ID: 0x2c Chip ID: 0xda
NAND: Page Bytes: 2048, Spare Bytes: 64
NAND: ECC Correctability Bits: 4, ECC Sector Bytes: 512
NAND: Disable On-Die ECC
NAND: Initialize PMECC params, cap: 4, sector: 512
NAND: Image: Copy 0x100000 bytes from 0x40000 to 0x26f00000
NAND: Done to load image
<debug_uart>
AT91Bootstrap 4.0.5-gitAUTOINC+8fe4b67188-r0.tano3.2 (2022-11-09 13:05:42)
NAND: ONFI flash detected
NAND: Manufacturer ID: 0x2c Chip ID: 0xda
NAND: Page Bytes: 2048, Spare Bytes: 64
NAND: ECC Correctability Bits: 4, ECC Sector Bytes: 512
NAND: Disable On-Die ECC
NAND: Initialize PMECC params, cap: 4, sector: 512
NAND: Image: Copy 0xc0000 bytes from 0x40000 to 0x26f00000
NAND: Done to load image
<debug_uart>
3.12.2.2 U-Boot
U-Boot 2023.07.02-gitAUTOINC+842d9d53a1-tano0.3 (Dec 18 2023 - 10:10:05 +0000)
CPU: SAMA5D36
Crystal frequency: 12 MHz
CPU clock : 528 MHz
Master clock : 132 MHz
DRAM: 256 MiB
Core: 207 devices, 20 uclasses, devicetree: separate
WDT: Started watchdog@fffffe40 with servicing every 1000ms (15s timeout)
NAND: 256 MiB
MMC: Atmel mci: 0, Atmel mci: 1
Loading Environment from NAND... OK
In: serial@ffffee00
Out: serial@ffffee00
Err: serial@ffffee00
Net:
Warning: ethernet@f0028000 MAC addresses don't match:
Address in ROM is00:10:a1:98:97:02
Address in environment is00:10:a1:98:97:01
eth0: ethernet@f0028000
Hit any key to stop autoboot: 3 2 1 0
NAND read: device 0 offset 0x180000, size 0x40000
262144 bytes read: OK
## Executing script at 21000000
Board name: sama5d3_xplained
Active system A
Loading kernel fitImage...
ubi0: attaching mtd5
ubi0: scanning is finished
ubi0: attached mtd5 (name "system_a", size 104 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 832, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 32/25, WL threshold: 4096, image sequence number: 345045444
ubi0: available PEBs: 539, total reserved PEBs: 293, PEBs reserved for bad PEB handling: 40
No size specified -> Using max size (6348800)
Read 6348800 bytes from volume kernel to 24000000
Booting kernel 0x24000000#conf-at91-evb-ksz9477.dtb...
## Loading kernel from FIT Image at 24000000 ...
Using 'conf-at91-evb-ksz9477.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x24000110
Data Size: 6148472 Bytes = 5.9 MiB
Architecture: ARM
OS: Linux
Load Address: 0x22000000
Entry Point: 0x22000000
Hash algo: sha256
Hash value: 336c572dee71d4ab075f16d125b701ebd64e3575c8afa8e78305d7914443f6a2
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 24000000 ...
Using 'conf-at91-evb-ksz9477.dtb' configuration
Trying 'fdt-at91-evb-ksz9477.dtb' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x245dd39c
Data Size: 40674 Bytes = 39.7 KiB
Architecture: ARM
Load Address: 0x23e00000
Hash algo: sha256
Hash value: 0c6d7b5e399d6f517c27e2c6b4e493a0516448595cc808fe7a395121cd5babdc
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x245dd39c to 0x23e00000
Booting using the fdt blob at 0x23e00000
Working FDT set to 23e00000
Loading Kernel Image
Loading Device Tree to 2eb15000, end 2eb21ee1 ... OK
Working FDT set to 2eb15000
Starting kernel ...
U-Boot 2020.01-gitAUTOINC+af59b26c22-tano0.3 (Jan 15 2021 - 07:11:03 +0000)
CPU: SAMA5D36
Crystal frequency: 12 MHz
CPU clock : 528 MHz
Master clock : 132 MHz
DRAM: 256 MiB
WDT: Started with servicing (15s timeout)
NAND: 256 MiB
MMC: Atmel mci: 0, Atmel mci: 1
Loading Environment from NAND... OK
In: serial@ffffee00
Out: serial@ffffee00
Err: serial@ffffee00
Net:
Warning: ethernet@f0028000 MAC addresses don't match:
Address in ROM is 00:10:a1:98:97:02
Address in environment is 00:10:a1:98:97:01
eth0: ethernet@f0028000
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x180000, size 0x40000
262144 bytes read: OK
## Executing script at 21000000
Board name: sama5d3_xplained
Active system A
Loading kernel fitImage...
ubi0: attaching mtd5
ubi0: scanning is finished
ubi0: attached mtd5 (name "system_a", size 104 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 832, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 27/14, WL threshold: 4096, image sequence number: 1194712431
ubi0: available PEBs: 539, total reserved PEBs: 293, PEBs reserved for bad PEB handling: 40
No size specified -> Using max size (6348800)
Read 6348800 bytes from volume kernel to 24000000
Booting kernel 0x24000000#conf-at91-evb-ksz9477.dtb...
## Loading kernel from FIT Image at 24000000 ...
Using 'conf-at91-evb-ksz9477.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x24000110
Data Size: 6148552 Bytes = 5.9 MiB
Architecture: ARM
OS: Linux
Load Address: 0x22000000
Entry Point: 0x22000000
Hash algo: sha256
Hash value: 35c61ee1fc6bfb8075a64b942748fd784606a4f0811404fd0cb67a2725216ee1
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 24000000 ...
Using 'conf-at91-evb-ksz9477.dtb' configuration
Trying 'fdt-at91-evb-ksz9477.dtb' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x245dd3ec
Data Size: 40674 Bytes = 39.7 KiB
Architecture: ARM
Load Address: 0x23e00000
Hash algo: sha256
Hash value: 0c6d7b5e399d6f517c27e2c6b4e493a0516448595cc808fe7a395121cd5babdc
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x245dd3ec to 0x23e00000
Booting using the fdt blob at 0x23e00000
Loading Kernel Image
Loading Device Tree to 2fb20000, end 2fb2cee1 ... OK
Starting kernel ...
3.12.2.3 Linux Kernel (OS)
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.0.20.0.2 (oe-user@oe-host) (arm-oe-linux-gnueabi-gcc (GCC) 11.4.0, GNU ld (GNU Binutils) 2.38.20220708) #1 Tue Jan 23 16:07:43 UTC 2024
[ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Microchip EVB-KSZ9477
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x2e800000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000020000000-0x000000002fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000020000000-0x000000002fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000002fffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 ubi.mtd=system_a,2048 ubi.mtd=rootfs_data,2048 ubi.block=0,rootfs root=/dev/ubiblock0_1 ro rootfstype=squashfs rootwait rootfs_partition=system_a rootfs_volume=rootfs earlyprintk panic=15
[ 0.000000] Unknown kernel command line parameters "earlyprintk rootfs_partition=system_a rootfs_volume=rootfs", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 229076K/262144K available (9216K kernel code, 463K rwdata, 2384K rodata, 1024K init, 166K bss, 16684K reserved, 16384K cma-reserved)
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: pit: mask: 0xfffffff max_cycles: 0xfffffff, max_idle_ns: 14479245754 ns
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns
[ 0.000000] Calibrating delay loop... 351.43 BogoMIPS (lpj=1757184)
[ 0.060000] CPU: Testing write buffer coherency: ok
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.060000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.060000] Setting up static identity map for 0x20100000 - 0x20100060
[ 0.060000] devtmpfs: initialized
[ 0.070000] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 0.070000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.070000] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.080000] pinctrl core: initialized pinctrl subsystem
[ 0.080000] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.080000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.080000] cpuidle: using governor menu
[ 0.120000] AT91: PM: standby: standby, suspend: ulp0
[ 0.120000] gpio-at91 fffff200.gpio: at address (ptrval)
[ 0.120000] gpio-at91 fffff400.gpio: at address (ptrval)
[ 0.120000] gpio-at91 fffff600.gpio: at address (ptrval)
[ 0.120000] gpio-at91 fffff800.gpio: at address (ptrval)
[ 0.130000] gpio-at91 fffffa00.gpio: at address (ptrval)
[ 0.130000] pinctrl-at91 ahb:apb:pinctrl@fffff200: initialized AT91 pinctrl driver
[ 0.150000] at_hdmac ffffe600.dma-controller: Atmel AHB DMA Controller ( cpy set slave ), 8 channels
[ 0.150000] at_hdmac ffffe800.dma-controller: Atmel AHB DMA Controller ( cpy set slave ), 8 channels
[ 0.160000] AT91: Detected SoC family: sama5d3
[ 0.160000] AT91: Detected SoC: sama5d36, revision 2
[ 0.160000] SCSI subsystem initialized
[ 0.160000] usbcore: registered new interface driver usbfs
[ 0.160000] usbcore: registered new interface driver hub
[ 0.160000] usbcore: registered new device driver usb
[ 0.160000] at91_i2c f0014000.i2c: using dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers
[ 0.160000] i2c i2c-0: using pinctrl states for GPIO recovery
[ 0.160000] i2c i2c-0: using generic GPIOs for recovery
[ 0.160000] at91_i2c f0014000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.160000] at91_i2c f0018000.i2c: using dma0chan2 (tx) and dma0chan3 (rx) for DMA transfers
[ 0.160000] i2c i2c-1: using pinctrl states for GPIO recovery
[ 0.160000] i2c i2c-1: using generic GPIOs for recovery
[ 0.160000] at91_i2c f0018000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.160000] at91_i2c f801c000.i2c: can't get DMA channel, continue without DMA support
[ 0.170000] i2c i2c-2: using pinctrl states for GPIO recovery
[ 0.170000] i2c i2c-2: using generic GPIOs for recovery
[ 0.170000] at91_i2c f801c000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.170000] mc: Linux media interface: v0.10
[ 0.170000] videodev: Linux video capture interface: v2.00
[ 0.170000] pps_core: LinuxPPS API ver. 1 registered
[ 0.170000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.170000] PTP clock support registered
[ 0.170000] Advanced Linux Sound Architecture Driver Initialized.
[ 0.170000] Bluetooth: Core ver 2.22
[ 0.170000] NET: Registered PF_BLUETOOTH protocol family
[ 0.170000] Bluetooth: HCI device and connection manager initialized
[ 0.170000] Bluetooth: HCI socket layer initialized
[ 0.170000] Bluetooth: L2CAP socket layer initialized
[ 0.170000] Bluetooth: SCO socket layer initialized
[ 0.170000] clocksource: Switched to clocksource pit
[ 0.200000] NET: Registered PF_INET protocol family
[ 0.200000] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.210000] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.210000] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.210000] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.210000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.210000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.210000] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.210000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.210000] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.210000] RPC: Registered named UNIX socket transport module.
[ 0.210000] RPC: Registered udp transport module.
[ 0.210000] RPC: Registered tcp transport module.
[ 0.210000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.210000] Initialise system trusted keyrings
[ 0.210000] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.210000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] Key type asymmetric registered
[ 0.420000] Asymmetric key parser 'x509' registered
[ 0.420000] io scheduler mq-deadline registered
[ 0.420000] io scheduler kyber registered
[ 0.440000] brd: module loaded
[ 0.460000] loop: module loaded
[ 0.460000] atmel_usart_serial.0.auto: ttyS1 at MMIO 0xf001c000 (irq = 27, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.460000] atmel_usart_serial.1.auto: ttyS2 at MMIO 0xf0020000 (irq = 28, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.460000] atmel_usart_serial.2.auto: ttyS5 at MMIO 0xf0024000 (irq = 29, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.470000] atmel_usart_serial.3.auto: ttyS0 at MMIO 0xffffee00 (irq = 30, base_baud = 8250000) is a ATMEL_SERIAL
[ 1.130000] printk: console [ttyS0] enabled
[ 1.140000] atmel_spi f0004000.spi: Using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers
[ 1.150000] atmel_spi f0004000.spi: Atmel SPI Controller version 0x213 at 0xf0004000 (irq 31)
[ 1.160000] atmel_spi f8008000.spi: Using dma1chan0 (tx) and dma1chan1 (rx) for DMA transfers
[ 1.170000] ksz9477@0 enforce active low on chipselect handle
[ 1.180000] atmel_spi f8008000.spi: Atmel SPI Controller version 0x213 at 0xf8008000 (irq 32)
[ 1.190000] CAN device driver interface
[ 1.190000] ksz9477-switch spi1.0: Microchip KSZ switch driver version 0.9.0
[ 1.200000] ksz9477-switch spi1.0: Microchip KSZ9477 Switch (7 ports)
[ 1.210000] ksz9477-switch spi1.0: Failed to register DSA switch (-517)
[ 1.860000] macb f0028000.ethernet eth0: Cadence GEM rev 0x00020119 at 0xf0028000 irq 34 (00:10:a1:98:97:01)
[ 1.870000] PPP generic driver version 2.4.2
[ 1.870000] PPP MPPE Compression module registered
[ 1.880000] NET: Registered PF_PPPOX protocol family
[ 1.890000] atmel-ehci 700000.ehci: EHCI Host Controller
[ 1.890000] atmel-ehci 700000.ehci: new USB bus registered, assigned bus number 1
[ 1.900000] atmel-ehci 700000.ehci: irq 35, io mem 0x00700000
[ 1.940000] atmel-ehci 700000.ehci: USB 2.0 started, EHCI 1.00
[ 1.940000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 1.950000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.960000] usb usb1: Product: EHCI Host Controller
[ 1.960000] usb usb1: Manufacturer: Linux 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.0.20.0.2 ehci_hcd
[ 1.970000] usb usb1: SerialNumber: 700000.ehci
[ 1.980000] hub 1-0:1.0: USB hub found
[ 1.980000] hub 1-0:1.0: 3 ports detected
[ 1.990000] at91_ohci 600000.ohci: USB Host Controller
[ 1.990000] at91_ohci 600000.ohci: new USB bus registered, assigned bus number 2
[ 2.000000] at91_ohci 600000.ohci: irq 35, io mem 0x00600000
[ 2.080000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[ 2.090000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.090000] usb usb2: Product: USB Host Controller
[ 2.100000] usb usb2: Manufacturer: Linux 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.0.20.0.2 ohci_hcd
[ 2.110000] usb usb2: SerialNumber: at91
[ 2.110000] hub 2-0:1.0: USB hub found
[ 2.120000] hub 2-0:1.0: 3 ports detected
[ 2.120000] usbcore: registered new interface driver cdc_acm
[ 2.130000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.140000] usbcore: registered new interface driver usb-storage
[ 2.150000] usbcore: registered new interface driver usbserial_generic
[ 2.150000] usbserial: USB Serial support registered for generic
[ 2.160000] usbcore: registered new interface driver ftdi_sio
[ 2.160000] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.170000] at91_rtc fffffeb0.rtc: registered as rtc0
[ 2.180000] at91_rtc fffffeb0.rtc: setting system clock to 2024-04-04T11:33:02 UTC (1712230382)
[ 2.190000] at91_rtc fffffeb0.rtc: AT91 Real Time Clock driver.
[ 2.190000] i2c_dev: i2c /dev entries driver
[ 2.200000] at91-reset fffffe00.reset-controller: Starting after wakeup
[ 2.210000] at91_wdt fffffe40.watchdog: watchdog already configured differently (mr = 1fff2eff expecting 1fff2fff)
[ 2.220000] at91sam9_wdt: enabled (heartbeat=15 sec, nowayout=0)
[ 2.230000] Bluetooth: HCI UART driver ver 2.3
[ 2.230000] Bluetooth: HCI UART protocol H4 registered
[ 2.240000] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 2.240000] usbcore: registered new interface driver btusb
[ 2.250000] sdhci: Secure Digital Host Controller Interface driver
[ 2.260000] sdhci: Copyright(c) Pierre Ossman
[ 2.260000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.270000] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.270000] atmel_aes f8038000.crypto: version: 0x135
[ 2.280000] atmel_aes f8038000.crypto: Atmel AES - Using dma1chan2, dma1chan3 for DMA transfers
[ 2.290000] atmel_sha f8034000.crypto: version: 0x410
[ 2.290000] atmel_sha f8034000.crypto: using dma1chan4 for DMA transfers
[ 2.300000] atmel_sha f8034000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512
[ 2.310000] atmel_tdes f803c000.crypto: version: 0x701
[ 2.310000] atmel_tdes f803c000.crypto: using dma1chan5, dma1chan6 for DMA transfers
[ 2.320000] atmel_tdes f803c000.crypto: Atmel DES/TDES
[ 2.330000] usbcore: registered new interface driver usbhid
[ 2.330000] usbhid: USB HID core driver
[ 2.340000] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 2.350000] nand: Micron MT29F2G08ABAEAWP
[ 2.350000] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.360000] atmel_mci f0000000.mmc: version: 0x505
[ 2.370000] atmel_mci f0000000.mmc: using dma0chan7 for DMA transfers
[ 2.380000] atmel_mci f8000000.mmc: version: 0x505
[ 2.380000] atmel_mci f8000000.mmc: using dma1chan7 for DMA transfers
[ 2.390000] Bad block table found at page 131008, version 0x01
[ 2.390000] Bad block table found at page 130944, version 0x01
[ 2.400000] atmel_mci f0000000.mmc: Atmel MCI controller at 0xf0000000 irq 42, 1 slots
[ 2.410000] 7 fixed-partitions partitions found on MTD device atmel_nand
[ 2.420000] Creating 7 MTD partitions on "atmel_nand":
[ 2.420000] 0x000000000000-0x000000040000 : "at91bootstrap"
[ 2.430000] atmel_mci f8000000.mmc: Atmel MCI controller at 0xf8000000 irq 43, 1 slots
[ 2.440000] 0x000000040000-0x000000180000 : "uboot"
[ 2.450000] 0x000000180000-0x0000001c0000 : "startup"
[ 2.460000] 0x0000001c0000-0x000000200000 : "ubootenv"
[ 2.470000] 0x000000200000-0x000006a00000 : "system_a"
[ 2.470000] 0x000006a00000-0x00000d200000 : "system_b"
[ 2.480000] 0x00000d200000-0x000010000000 : "rootfs_data"
[ 2.490000] iio iio:device0: Resolution used: 12 bits
[ 2.500000] iio iio:device0: ADC Touch screen is disabled.
[ 2.510000] u32 classifier
[ 2.510000] input device check on
[ 2.520000] Actions configured
[ 2.520000] NET: Registered PF_INET6 protocol family
[ 2.530000] Segment Routing with IPv6
[ 2.530000] In-situ OAM (IOAM) with IPv6
[ 2.540000] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.550000] NET: Registered PF_PACKET protocol family
[ 2.550000] Bridge firewalling registered
[ 2.560000] can: controller area network core
[ 2.560000] NET: Registered PF_CAN protocol family
[ 2.570000] can: raw protocol
[ 2.570000] can: broadcast manager protocol
[ 2.570000] can: netlink gateway - max_hops=1
[ 2.580000] Bluetooth: RFCOMM TTY layer initialized
[ 2.580000] Bluetooth: RFCOMM socket layer initialized
[ 2.590000] Bluetooth: RFCOMM ver 1.11
[ 2.590000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.600000] Bluetooth: BNEP filters: protocol multicast
[ 2.600000] Bluetooth: BNEP socket layer initialized
[ 2.610000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.610000] Bluetooth: HIDP socket layer initialized
[ 2.620000] l2tp_core: L2TP core driver, V2.0
[ 2.620000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 2.630000] l2tp_netlink: L2TP netlink interface
[ 2.630000] Loading compiled-in X.509 certificates
[ 2.670000] ksz9477-switch spi1.0: Microchip KSZ switch driver version 0.9.0
[ 2.680000] ksz9477-switch spi1.0: Microchip KSZ9477 Switch (7 ports)
[ 2.690000] ksz9477-switch spi1.0: Use rgmii-txid
[ 2.700000] ksz9477-switch spi1.0: Port 5: Enabled tail tagging
[ 2.720000] ksz9477-switch spi1.0: Enabled jumbo frames support
[ 2.720000] ksz9477-switch spi1.0: The switch has been successfully started
[ 2.740000] ksz9477-switch spi1.0: Using legacy PHYLIB callbacks. Please migrate to PHYLINK!
[ 2.750000] ksz9477-switch spi1.0 sw1p1 (uninitialized): PHY [dsa-0.0:00] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 2.770000] ksz9477-switch spi1.0 sw1p2 (uninitialized): PHY [dsa-0.0:01] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 2.780000] ksz9477-switch spi1.0 sw1p3 (uninitialized): PHY [dsa-0.0:02] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 2.790000] ksz9477-switch spi1.0 sw1p4 (uninitialized): PHY [dsa-0.0:03] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 2.810000] ksz9477-switch spi1.0 sw1p5 (uninitialized): PHY [dsa-0.0:04] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 2.820000] device eth0 entered promiscuous mode
[ 2.830000] DSA: tree 0 setup
[ 2.830000] ksz9477-switch spi1.0: User ports mask is 0x5f
[ 2.830000] ksz9477-switch spi1.0: CPU port MAC: 00:10:a1:98:97:01
[ 2.840000] ksz9477-switch spi1.0: Port 0 [sw1p1] MAC: 00:10:a1:98:97:02
[ 2.850000] ksz9477-switch spi1.0: Port 1 [sw1p2] MAC: 00:10:a1:98:97:03
[ 2.850000] ksz9477-switch spi1.0: Port 2 [sw1p3] MAC: 00:10:a1:98:97:04
[ 2.860000] ksz9477-switch spi1.0: Port 3 [sw1p4] MAC: 00:10:a1:98:97:05
[ 2.870000] ksz9477-switch spi1.0: Port 4 [sw1p5] MAC: 00:10:a1:98:97:06
[ 2.880000] ksz9477-switch spi1.0: Port 6 [sw1p6] MAC: 00:10:a1:98:97:07
[ 2.880000] ksz9477-switch spi1.0: Port mask: 0x7f, CPU mask: 0x20, DSA mask: 0x0, user mask: 0x5f
[ 2.890000] ksz9477-switch spi1.0: Port 0 [USER]: sw1p1
[ 2.900000] ksz9477-switch spi1.0: Port 1 [USER]: sw1p2
[ 2.900000] ksz9477-switch spi1.0: Port 2 [USER]: sw1p3
[ 2.910000] ksz9477-switch spi1.0: Port 3 [USER]: sw1p4
[ 2.910000] ksz9477-switch spi1.0: Port 4 [USER]: sw1p5
[ 2.920000] ksz9477-switch spi1.0: Port 5 [CPU]: eth0
[ 2.920000] ksz9477-switch spi1.0: Port 6 [USER]: sw1p6
[ 2.930000] ksz9477-switch spi1.0: DSA switch registered
[ 2.930000] ksz9477-switch spi1.0: Created sysfs entries
[ 2.940000] ubi0: default fastmap pool size: 40
[ 2.940000] ubi0: default fastmap WL pool size: 20
[ 2.950000] ubi0: attaching mtd4
[ 3.450000] ubi0: scanning is finished
[ 3.460000] ubi0: attached mtd4 (name "system_a", size 104 MiB)
[ 3.470000] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.480000] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.480000] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.490000] ubi0: good PEBs: 832, bad PEBs: 0, corrupted PEBs: 0
[ 3.500000] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.500000] ubi0: max/mean erase counter: 27/14, WL threshold: 4096, image sequence number: 1194712431
[ 3.510000] ubi0: available PEBs: 537, total reserved PEBs: 295, PEBs reserved for bad PEB handling: 40
[ 3.520000] ubi0: background thread "ubi_bgt0d" started, PID 100
[ 3.530000] ubi1: default fastmap pool size: 15
[ 3.530000] ubi1: default fastmap WL pool size: 7
[ 3.540000] ubi1: attaching mtd6
[ 3.780000] ubi1: scanning is finished
[ 3.790000] ubi1: attached mtd6 (name "rootfs_data", size 46 MiB)
[ 3.800000] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.810000] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.810000] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.820000] ubi1: good PEBs: 364, bad PEBs: 4, corrupted PEBs: 0
[ 3.830000] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 3.830000] ubi1: max/mean erase counter: 31/16, WL threshold: 4096, image sequence number: 40562245
[ 3.840000] ubi1: available PEBs: 0, total reserved PEBs: 364, PEBs reserved for bad PEB handling: 36
[ 3.850000] ubi1: background thread "ubi_bgt1d" started, PID 101
[ 3.860000] block ubiblock0_1: created from ubi0:1(rootfs)
[ 3.870000] ALSA device list:
[ 3.870000] No soundcards found.
[ 3.880000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.890000] devtmpfs: mounted
[ 3.890000] Freeing unused kernel image (initmem) memory: 1024K
[ 3.900000] Run /sbin/init as init process
[ 4.120000] init: Console is alive
[ 4.120000] init: - watchdog -
[ 5.150000] random: crng init done
[ 5.480000] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.510000] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.540000] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.960000] SWUPDATE: AT91Bootstrap version 4.0.5-gitAUTOINC+8fe4b67188-r0.tano3.2
[ 10.340000] SWUPDATE: U-Boot version 2020.01-gitAUTOINC+af59b26c22-tano0.3
[ 10.460000] SWUPDATE: U-Boot startup version 1.0.0-tano1.atmel1
[ 10.500000] SWUPDATE: Kernel version 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.0.20.0.2
[ 10.530000] SWUPDATE: Read-only filesystem version 2024-04-04-08-26-34-UTC
[ 10.800000] mount_root: loading kmods from internal overlay
[ 11.170000] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 11.180000] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 11.330000] UBIFS (ubi1:0): default file-system created
[ 11.330000] UBIFS (ubi1:0): Mounting in unauthenticated mode
[ 11.340000] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 187
[ 11.430000] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[ 11.440000] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.450000] UBIFS (ubi1:0): FS size: 39616512 bytes (37 MiB, 312 LEBs), max 322 LEBs, journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 11.460000] UBIFS (ubi1:0): reserved for root: 1871185 bytes (1827 KiB)
[ 11.460000] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID A5149243-9568-4239-AFCF-A89B56166F28, small LPT model
[ 11.470000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 11.470000] block: unable to load configuration (fstab: Entry not found)
[ 11.480000] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 11.490000] block: unable to load configuration (fstab: Entry not found)
[ 11.490000] block: attempting to load /etc/config/fstab
[ 11.510000] block: extroot: not configured
[ 11.520000] UBIFS (ubi1:0): un-mount UBI device 1
[ 11.530000] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" stops
[ 11.540000] UBIFS (ubi1:0): Mounting in unauthenticated mode
[ 11.540000] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 188
[ 11.630000] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[ 11.640000] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.650000] UBIFS (ubi1:0): FS size: 39616512 bytes (37 MiB, 312 LEBs), max 322 LEBs, journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 11.660000] UBIFS (ubi1:0): reserved for root: 1871185 bytes (1827 KiB)
[ 11.670000] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID A5149243-9568-4239-AFCF-A89B56166F28, small LPT model
[ 11.770000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 11.770000] block: unable to load configuration (fstab: Entry not found)
[ 11.780000] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 11.790000] block: unable to load configuration (fstab: Entry not found)
[ 11.790000] block: attempting to load /etc/config/fstab
[ 11.800000] block: extroot: not configured
[ 11.810000] mount_root: overlay filesystem has not been fully initialized yet
[ 11.820000] mount_root: switching to ubifs overlay
[ 12.040000] Root filesystem mounted
[ 14.530000] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 14.610000] procd: - watchdog -
[ 14.630000] procd: - ubus -
[ 14.730000] procd: - init -
Please press Enter to activate this console.
[ 18.750000] kmodloader: loading kernel modules from /etc/modules.d/*
[ 18.800000] tun: Universal TUN/TAP device driver, 1.6
[ 19.010000] atmel_usba_udc 500000.gadget: MMIO registers at [mem 0xf8030000-0xf8033fff] mapped at 7cbdddcf
[ 19.020000] atmel_usba_udc 500000.gadget: FIFO at [mem 0x00500000-0x005fffff] mapped at 90c2ba9d
[ 19.050000] usbcore: registered new interface driver cdc_wdm
[ 19.120000] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 19.410000] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 19.420000] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[ 19.430000] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 19.440000] cfg80211: failed to load regulatory.db
[ 19.450000] cryptodev: loading out-of-tree module taints kernel.
[ 19.480000] cryptodev: driver 1.12 loaded.
[ 19.500000] gre: GRE over IPv4 demultiplexor driver
[ 19.660000] PPTP driver version 0.8.5
[ 19.790000] xt_time: kernel timezone is +0300
[ 19.800000] usbcore: registered new interface driver cdc_ether
[ 19.820000] usbcore: registered new interface driver cdc_ncm
[ 19.900000] usbcore: registered new interface driver qmi_wwan
[ 19.970000] usbcore: registered new interface driver cdc_mbim
[ 20.010000] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 32.690000] Cgroup memory moving (move_charge_at_immigrate) is deprecated. Please report your usecase to linux-mm@kvack.org if you depend on this functionality.
[ 37.230000] udevd[1374]: starting version 3.2.10
[ 37.530000] udevd[1374]: starting eudev-3.2.10
[ 79.710000] macb f0028000.ethernet eth0: configuring for fixed/rgmii link mode
[ 79.720000] macb f0028000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 79.720000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 79.820000] ksz9477-switch spi1.0 sw1p1: configuring for phy/gmii link mode
[ 79.860000] ksz9477-switch spi1.0 sw1p1: Link is Up - 1Gbps/Full - flow control off
[ 79.870000] br-lan: port 1(sw1p1) entered blocking state
[ 79.870000] br-lan: port 1(sw1p1) entered disabled state
[ 79.920000] device sw1p1 entered promiscuous mode
[ 79.960000] br-lan: port 1(sw1p1) entered blocking state
[ 80.100000] ksz9477-switch spi1.0 sw1p2: configuring for phy/gmii link mode
[ 80.140000] br-lan: port 2(sw1p2) entered blocking state
[ 80.140000] br-lan: port 2(sw1p2) entered disabled state
[ 80.250000] device sw1p2 entered promiscuous mode
[ 80.380000] ksz9477-switch spi1.0 sw1p3: configuring for phy/gmii link mode
[ 80.420000] br-lan: port 3(sw1p3) entered blocking state
[ 80.420000] br-lan: port 3(sw1p3) entered disabled state
[ 80.520000] device sw1p3 entered promiscuous mode
[ 80.610000] ksz9477-switch spi1.0 sw1p4: configuring for phy/gmii link mode
[ 80.660000] br-lan: port 4(sw1p4) entered blocking state
[ 80.660000] br-lan: port 4(sw1p4) entered disabled state
[ 80.700000] device sw1p4 entered promiscuous mode
[ 80.800000] ksz9477-switch spi1.0 sw1p6: configuring for fixed/ link mode
[ 80.810000] ksz9477-switch spi1.0 sw1p6: Link is Up - 1Gbps/Full - flow control off
[ 80.850000] br-lan: port 5(sw1p6) entered blocking state
[ 80.860000] br-lan: port 5(sw1p6) entered disabled state
[ 80.880000] ksz9477-switch spi1.0 sw1p1: Link is Down
[ 80.910000] device sw1p6 entered promiscuous mode
[ 80.920000] br-lan: port 5(sw1p6) entered blocking state
[ 80.960000] br-lan: port 1(sw1p1) entered disabled state
[ 81.090000] ksz9477-switch spi1.0 sw1p5: configuring for phy/gmii link mode
[ 84.000000] ksz9477-switch spi1.0 sw1p1: Link is Up - 1Gbps/Full - flow control off
[ 84.000000] br-lan: port 1(sw1p1) entered blocking state
[ 87.700000] br-lan: port 1(sw1p1) entered blocking state
[ 87.790000] br-lan: port 5(sw1p6) entered blocking state
[ 88.870000] br-lan: port 1(sw1p1) entered learning state
[ 88.880000] br-lan: port 1(sw1p1) entered forwarding state
[ 88.880000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 89.830000] br-lan: port 5(sw1p6) entered learning state
[ 89.830000] br-lan: port 5(sw1p6) entered forwarding state
[ 119.620000] using random self ethernet address
[ 119.620000] using random host ethernet address
[ 119.630000] usb0: HOST MAC 26:50:14:39:a2:e0
[ 119.630000] usb0: MAC 5e:be:9f:13:94:2b
[ 119.630000] using random self ethernet address
[ 119.640000] using random host ethernet address
[ 119.640000] g_ether gadget.0: Ethernet Gadget, version: Memorial Day 2008
[ 119.650000] g_ether gadget.0: g_ether ready
tanowrt login: root
Password:
_______ __ __ _
|__ __| \ \ / / | | Embedded Linux Distribution
| | __ _ _ __ __\ \ /\ / / __| |_ by Tano Systems
| |/ _` | '_ \ / _ \ \/ \/ / '__| __|
| | (_| | | | | (_) \ /\ /| | | |_ (c) 2018-2024 Tano Systems LLC
|_|\__,_|_| |_|\___/ \/ \/ |_| \__| https://tano-systems.com
Board: Microchip EVB-KSZ9477 (NAND)
Release: Kirkstone
Revision: c584e770702714a974a197294fe4849559ac995c
2024-04-04 08:26:34 UTC
[root@tanowrt ~]#
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.105-tano-mchp-standard-g03bed3badd-tano0.2.2.20.0.2 (oe-user@oe-host) (arm-oe-linux-gnueabi-gcc (GCC) 11.4.0, GNU ld (GNU Binutils) 2.38.20220708) #1 Tue Apr 25 15:12:32 UTC 2023
[ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Microchip EVB-KSZ9477
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x2f000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000020000000-0x000000002fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000020000000-0x000000002fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000002fffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 ubi.mtd=system_b,2048 ubi.mtd=rootfs_data,2048 ubi.block=0,rootfs root=/dev/ubiblock0_1 ro rootfstype=squashfs rootwait rootfs_partition=system_b rootfs_volume=rootfs earlyprintk panic=15
[ 0.000000] Unknown kernel command line parameters "earlyprintk rootfs_partition=system_b rootfs_volume=rootfs", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 229080K/262144K available (9216K kernel code, 457K rwdata, 2196K rodata, 1024K init, 166K bss, 16680K reserved, 16384K cma-reserved)
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: pit: mask: 0xfffffff max_cycles: 0xfffffff, max_idle_ns: 14479245754 ns
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns
[ 0.000000] Calibrating delay loop... 351.43 BogoMIPS (lpj=1757184)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.060000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.060000] CPU: Testing write buffer coherency: ok
[ 0.060000] Setting up static identity map for 0x20100000 - 0x20100060
[ 0.060000] devtmpfs: initialized
[ 0.080000] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 0.080000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.080000] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.080000] pinctrl core: initialized pinctrl subsystem
[ 0.080000] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.080000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.090000] cpuidle: using governor menu
[ 0.130000] AT91: PM: standby: standby, suspend: ulp0
[ 0.130000] gpio-at91 fffff200.gpio: at address (ptrval)
[ 0.130000] gpio-at91 fffff400.gpio: at address (ptrval)
[ 0.130000] gpio-at91 fffff600.gpio: at address (ptrval)
[ 0.130000] gpio-at91 fffff800.gpio: at address (ptrval)
[ 0.130000] gpio-at91 fffffa00.gpio: at address (ptrval)
[ 0.140000] pinctrl-at91 ahb:apb:pinctrl@fffff200: initialized AT91 pinctrl driver
[ 0.170000] at_hdmac ffffe600.dma-controller: Atmel AHB DMA Controller ( cpy set slave ), 8 channels
[ 0.170000] at_hdmac ffffe800.dma-controller: Atmel AHB DMA Controller ( cpy set slave ), 8 channels
[ 0.170000] AT91: Detected SoC family: sama5d3
[ 0.170000] AT91: Detected SoC: sama5d36, revision 2
[ 0.170000] SCSI subsystem initialized
[ 0.170000] usbcore: registered new interface driver usbfs
[ 0.170000] usbcore: registered new interface driver hub
[ 0.170000] usbcore: registered new device driver usb
[ 0.180000] at91_i2c f0014000.i2c: using dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers
[ 0.180000] i2c i2c-0: using pinctrl states for GPIO recovery
[ 0.180000] i2c i2c-0: using generic GPIOs for recovery
[ 0.180000] at91_i2c f0014000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.180000] at91_i2c f0018000.i2c: using dma0chan2 (tx) and dma0chan3 (rx) for DMA transfers
[ 0.180000] i2c i2c-1: using pinctrl states for GPIO recovery
[ 0.180000] i2c i2c-1: using generic GPIOs for recovery
[ 0.180000] at91_i2c f0018000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.180000] at91_i2c f801c000.i2c: can't get DMA channel, continue without DMA support
[ 0.180000] i2c i2c-2: using pinctrl states for GPIO recovery
[ 0.180000] i2c i2c-2: using generic GPIOs for recovery
[ 0.180000] at91_i2c f801c000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.180000] mc: Linux media interface: v0.10
[ 0.180000] videodev: Linux video capture interface: v2.00
[ 0.180000] pps_core: LinuxPPS API ver. 1 registered
[ 0.180000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.180000] PTP clock support registered
[ 0.180000] Advanced Linux Sound Architecture Driver Initialized.
[ 0.180000] Bluetooth: Core ver 2.22
[ 0.180000] NET: Registered PF_BLUETOOTH protocol family
[ 0.180000] Bluetooth: HCI device and connection manager initialized
[ 0.180000] Bluetooth: HCI socket layer initialized
[ 0.180000] Bluetooth: L2CAP socket layer initialized
[ 0.180000] Bluetooth: SCO socket layer initialized
[ 0.180000] clocksource: Switched to clocksource pit
[ 0.210000] NET: Registered PF_INET protocol family
[ 0.210000] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.210000] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.210000] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.210000] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.210000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.210000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.210000] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.210000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.210000] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.220000] RPC: Registered named UNIX socket transport module.
[ 0.220000] RPC: Registered udp transport module.
[ 0.220000] RPC: Registered tcp transport module.
[ 0.220000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.220000] Initialise system trusted keyrings
[ 0.220000] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.220000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] Key type asymmetric registered
[ 0.420000] Asymmetric key parser 'x509' registered
[ 0.420000] io scheduler mq-deadline registered
[ 0.420000] io scheduler kyber registered
[ 0.440000] brd: module loaded
[ 0.460000] loop: module loaded
[ 0.460000] atmel_usart_serial.0.auto: ttyS1 at MMIO 0xf001c000 (irq = 23, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.460000] atmel_usart_serial.1.auto: ttyS2 at MMIO 0xf0020000 (irq = 24, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.470000] atmel_usart_serial.2.auto: ttyS5 at MMIO 0xf0024000 (irq = 25, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.470000] atmel_usart_serial.3.auto: ttyS0 at MMIO 0xffffee00 (irq = 38, base_baud = 8250000) is a ATMEL_SERIAL
[ 1.120000] printk: console [ttyS0] enabled
[ 1.130000] atmel_spi f0004000.spi: Using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers
[ 1.140000] atmel_spi f0004000.spi: Atmel SPI Controller version 0x213 at 0xf0004000 (irq 19)
[ 1.150000] atmel_spi f8008000.spi: Using dma1chan0 (tx) and dma1chan1 (rx) for DMA transfers
[ 1.160000] ksz9477@0 enforce active low on chipselect handle
[ 1.170000] atmel_spi f8008000.spi: Atmel SPI Controller version 0x213 at 0xf8008000 (irq 28)
[ 1.180000] CAN device driver interface
[ 1.180000] ksz9477-switch spi1.0: Microchip KSZ switch driver version 0.9.0
[ 1.190000] ksz9477-switch spi1.0: Microchip KSZ9477 Switch (7 ports)
[ 1.200000] ksz9477-switch spi1.0: Failed to register DSA switch (-517)
[ 1.850000] macb f0028000.ethernet eth0: Cadence GEM rev 0x00020119 at 0xf0028000 irq 46 (00:10:a1:98:97:01)
[ 1.860000] PPP generic driver version 2.4.2
[ 1.860000] PPP MPPE Compression module registered
[ 1.870000] NET: Registered PF_PPPOX protocol family
[ 1.870000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.880000] ehci-atmel: EHCI Atmel driver
[ 1.890000] atmel-ehci 700000.ehci: EHCI Host Controller
[ 1.890000] atmel-ehci 700000.ehci: new USB bus registered, assigned bus number 1
[ 1.900000] atmel-ehci 700000.ehci: irq 49, io mem 0x00700000
[ 1.930000] atmel-ehci 700000.ehci: USB 2.0 started, EHCI 1.00
[ 1.930000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[ 1.940000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.950000] usb usb1: Product: EHCI Host Controller
[ 1.950000] usb usb1: Manufacturer: Linux 5.15.105-tano-mchp-standard-g03bed3badd-tano0.2.2.20.0.2 ehci_hcd
[ 1.960000] usb usb1: SerialNumber: 700000.ehci
[ 1.970000] hub 1-0:1.0: USB hub found
[ 1.970000] hub 1-0:1.0: 3 ports detected
[ 1.980000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.980000] ohci-atmel: OHCI Atmel driver
[ 1.990000] at91_ohci 600000.ohci: USB Host Controller
[ 1.990000] at91_ohci 600000.ohci: new USB bus registered, assigned bus number 2
[ 2.000000] at91_ohci 600000.ohci: irq 49, io mem 0x00600000
[ 2.080000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.15
[ 2.090000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.100000] usb usb2: Product: USB Host Controller
[ 2.100000] usb usb2: Manufacturer: Linux 5.15.105-tano-mchp-standard-g03bed3badd-tano0.2.2.20.0.2 ohci_hcd
[ 2.110000] usb usb2: SerialNumber: at91
[ 2.110000] hub 2-0:1.0: USB hub found
[ 2.120000] hub 2-0:1.0: 3 ports detected
[ 2.120000] usbcore: registered new interface driver cdc_acm
[ 2.130000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.140000] usbcore: registered new interface driver usb-storage
[ 2.140000] usbcore: registered new interface driver usbserial_generic
[ 2.150000] usbserial: USB Serial support registered for generic
[ 2.160000] usbcore: registered new interface driver ftdi_sio
[ 2.160000] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.170000] at91_rtc fffffeb0.rtc: registered as rtc0
[ 2.180000] at91_rtc fffffeb0.rtc: setting system clock to 2024-04-12T11:36:28 UTC (1712921788)
[ 2.190000] at91_rtc fffffeb0.rtc: AT91 Real Time Clock driver.
[ 2.190000] i2c_dev: i2c /dev entries driver
[ 2.200000] at91-reset fffffe00.rstc: Starting after software reset
[ 2.210000] at91_wdt fffffe40.watchdog: watchdog already configured differently (mr = 1fff2eff expecting 1fff2fff)
[ 2.220000] at91sam9_wdt: enabled (heartbeat=15 sec, nowayout=0)
[ 2.230000] Bluetooth: HCI UART driver ver 2.3
[ 2.230000] Bluetooth: HCI UART protocol H4 registered
[ 2.240000] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 2.240000] usbcore: registered new interface driver btusb
[ 2.250000] sdhci: Secure Digital Host Controller Interface driver
[ 2.260000] sdhci: Copyright(c) Pierre Ossman
[ 2.260000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.270000] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.270000] atmel_aes f8038000.crypto: version: 0x135
[ 2.280000] atmel_mci f0000000.mmc: version: 0x505
[ 2.280000] atmel_mci f0000000.mmc: using dma0chan6 for DMA transfers
[ 2.290000] atmel_mci f8000000.mmc: version: 0x505
[ 2.300000] atmel_mci f8000000.mmc: using dma1chan4 for DMA transfers
[ 2.310000] atmel_aes f8038000.crypto: Atmel AES - Using dma1chan2, dma1chan3 for DMA transfers
[ 2.320000] atmel_sha f8034000.crypto: version: 0x410
[ 2.320000] atmel_sha f8034000.crypto: using dma1chan5 for DMA transfers
[ 2.330000] atmel_mci f0000000.mmc: Atmel MCI controller at 0xf0000000 irq 18, 1 slots
[ 2.340000] atmel_sha f8034000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512
[ 2.350000] atmel_tdes f803c000.crypto: version: 0x701
[ 2.350000] atmel_tdes f803c000.crypto: using dma1chan6, dma1chan7 for DMA transfers
[ 2.360000] atmel_mci f8000000.mmc: Atmel MCI controller at 0xf8000000 irq 27, 1 slots
[ 2.370000] atmel_tdes f803c000.crypto: Atmel DES/TDES
[ 2.380000] usbcore: registered new interface driver usbhid
[ 2.390000] usbhid: USB HID core driver
[ 2.390000] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 2.400000] nand: Micron MT29F2G08ABAEAWP
[ 2.400000] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.410000] Bad block table found at page 131008, version 0x01
[ 2.420000] Bad block table found at page 130944, version 0x01
[ 2.430000] 7 fixed-partitions partitions found on MTD device atmel_nand
[ 2.430000] Creating 7 MTD partitions on "atmel_nand":
[ 2.440000] 0x000000000000-0x000000040000 : "at91bootstrap"
[ 2.450000] 0x000000040000-0x000000180000 : "uboot"
[ 2.450000] 0x000000180000-0x0000001c0000 : "startup"
[ 2.460000] 0x0000001c0000-0x000000200000 : "ubootenv"
[ 2.470000] 0x000000200000-0x000006a00000 : "system_a"
[ 2.480000] 0x000006a00000-0x00000d200000 : "system_b"
[ 2.490000] 0x00000d200000-0x000010000000 : "rootfs_data"
[ 2.500000] iio iio:device0: Resolution used: 12 bits
[ 2.500000] iio iio:device0: ADC Touch screen is disabled.
[ 2.520000] u32 classifier
[ 2.520000] input device check on
[ 2.520000] Actions configured
[ 2.530000] NET: Registered PF_INET6 protocol family
[ 2.530000] Segment Routing with IPv6
[ 2.540000] In-situ OAM (IOAM) with IPv6
[ 2.540000] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.550000] NET: Registered PF_PACKET protocol family
[ 2.550000] Bridge firewalling registered
[ 2.560000] can: controller area network core
[ 2.560000] NET: Registered PF_CAN protocol family
[ 2.570000] can: raw protocol
[ 2.570000] can: broadcast manager protocol
[ 2.580000] can: netlink gateway - max_hops=1
[ 2.580000] Bluetooth: RFCOMM TTY layer initialized
[ 2.590000] Bluetooth: RFCOMM socket layer initialized
[ 2.590000] Bluetooth: RFCOMM ver 1.11
[ 2.590000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.600000] Bluetooth: BNEP filters: protocol multicast
[ 2.600000] Bluetooth: BNEP socket layer initialized
[ 2.610000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.620000] Bluetooth: HIDP socket layer initialized
[ 2.620000] l2tp_core: L2TP core driver, V2.0
[ 2.630000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 2.630000] l2tp_netlink: L2TP netlink interface
[ 2.640000] Loading compiled-in X.509 certificates
[ 2.660000] ksz9477-switch spi1.0: Microchip KSZ switch driver version 0.9.0
[ 2.660000] ksz9477-switch spi1.0: Microchip KSZ9477 Switch (7 ports)
[ 2.680000] ksz9477-switch spi1.0: Use rgmii-txid
[ 2.680000] ksz9477-switch spi1.0: Port 5: Enabled tail tagging
[ 2.710000] ksz9477-switch spi1.0: Enabled jumbo frames support
[ 2.720000] ksz9477-switch spi1.0: The switch has been successfully started
[ 2.730000] ksz9477-switch spi1.0 sw1p1 (uninitialized): PHY [dsa-0.0:00] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 2.750000] ksz9477-switch spi1.0 sw1p2 (uninitialized): PHY [dsa-0.0:01] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 2.760000] ksz9477-switch spi1.0 sw1p3 (uninitialized): PHY [dsa-0.0:02] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 2.770000] ksz9477-switch spi1.0 sw1p4 (uninitialized): PHY [dsa-0.0:03] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 2.790000] ksz9477-switch spi1.0 sw1p5 (uninitialized): PHY [dsa-0.0:04] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 2.800000] ksz9477-switch spi1.0: Using legacy PHYLIB callbacks. Please migrate to PHYLINK!
[ 2.810000] DSA: tree 0 setup
[ 2.810000] ksz9477-switch spi1.0: User ports mask is 0x5f
[ 2.820000] ksz9477-switch spi1.0: CPU port MAC: 00:10:a1:98:97:01
[ 2.830000] ksz9477-switch spi1.0: Port 0 [sw1p1] MAC: 00:10:a1:98:97:02
[ 2.830000] ksz9477-switch spi1.0: Port 1 [sw1p2] MAC: 00:10:a1:98:97:03
[ 2.840000] ksz9477-switch spi1.0: Port 2 [sw1p3] MAC: 00:10:a1:98:97:04
[ 2.850000] ksz9477-switch spi1.0: Port 3 [sw1p4] MAC: 00:10:a1:98:97:05
[ 2.850000] ksz9477-switch spi1.0: Port 4 [sw1p5] MAC: 00:10:a1:98:97:06
[ 2.860000] ksz9477-switch spi1.0: Port 6 [sw1p6] MAC: 00:10:a1:98:97:07
[ 2.870000] ksz9477-switch spi1.0: Port mask: 0x7f, CPU mask: 0x20, DSA mask: 0x0, user mask: 0x5f
[ 2.880000] ksz9477-switch spi1.0: Port 0 [USER]: sw1p1
[ 2.880000] ksz9477-switch spi1.0: Port 1 [USER]: sw1p2
[ 2.890000] ksz9477-switch spi1.0: Port 2 [USER]: sw1p3
[ 2.890000] ksz9477-switch spi1.0: Port 3 [USER]: sw1p4
[ 2.900000] ksz9477-switch spi1.0: Port 4 [USER]: sw1p5
[ 2.900000] ksz9477-switch spi1.0: Port 5 [CPU]: eth0
[ 2.910000] ksz9477-switch spi1.0: Port 6 [USER]: sw1p6
[ 2.910000] ksz9477-switch spi1.0: DSA switch registered
[ 2.920000] ksz9477-switch spi1.0: Created sysfs entries
[ 2.920000] ubi0: default fastmap pool size: 40
[ 2.930000] ubi0: default fastmap WL pool size: 20
[ 2.930000] ubi0: attaching mtd5
[ 3.440000] ubi0: scanning is finished
[ 3.450000] ubi0: attached mtd5 (name "system_b", size 104 MiB)
[ 3.460000] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.470000] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.470000] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.480000] ubi0: good PEBs: 832, bad PEBs: 0, corrupted PEBs: 0
[ 3.490000] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.490000] ubi0: max/mean erase counter: 47/32, WL threshold: 4096, image sequence number: 635408651
[ 3.500000] ubi0: available PEBs: 540, total reserved PEBs: 292, PEBs reserved for bad PEB handling: 40
[ 3.510000] ubi0: background thread "ubi_bgt0d" started, PID 99
[ 3.520000] ubi1: default fastmap pool size: 15
[ 3.520000] ubi1: default fastmap WL pool size: 7
[ 3.530000] ubi1: attaching mtd6
[ 3.770000] ubi1: scanning is finished
[ 3.780000] ubi1: attached mtd6 (name "rootfs_data", size 46 MiB)
[ 3.790000] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.790000] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.800000] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.810000] ubi1: good PEBs: 364, bad PEBs: 4, corrupted PEBs: 0
[ 3.810000] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 3.820000] ubi1: max/mean erase counter: 51/26, WL threshold: 4096, image sequence number: 814988759
[ 3.830000] ubi1: available PEBs: 0, total reserved PEBs: 364, PEBs reserved for bad PEB handling: 36
[ 3.840000] ubi1: background thread "ubi_bgt1d" started, PID 100
[ 3.850000] block ubiblock0_1: created from ubi0:1(rootfs)
[ 3.850000] ALSA device list:
[ 3.860000] No soundcards found.
[ 3.870000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.880000] devtmpfs: mounted
[ 3.880000] Freeing unused kernel image (initmem) memory: 1024K
[ 3.890000] Run /sbin/init as init process
[ 4.120000] init: Console is alive
[ 4.120000] init: - watchdog -
[ 5.040000] random: crng init done
[ 5.250000] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.280000] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.310000] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.620000] SWUPDATE: AT91Bootstrap version 4.0.8-gitAUTOINC+c331a16179-r0.tano3.3
[ 9.970000] SWUPDATE: U-Boot version 2023.07.02-gitAUTOINC+842d9d53a1-tano0.3
[ 10.070000] SWUPDATE: U-Boot startup version 1.0.0-tano1.atmel1
[ 10.110000] SWUPDATE: Kernel version 5.15.105-tano-mchp-standard-g03bed3badd-tano0.2.2.20.0.2
[ 10.140000] SWUPDATE: Read-only filesystem version 2024-04-12-08-06-39-UTC
[ 10.470000] mount_root: loading kmods from internal overlay
[ 10.790000] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 10.800000] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 10.940000] UBIFS (ubi1:0): Mounting in unauthenticated mode
[ 10.940000] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 189
[ 10.990000] UBIFS (ubi1:0): recovery needed
[ 11.090000] UBIFS (ubi1:0): recovery completed
[ 11.090000] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[ 11.100000] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.110000] UBIFS (ubi1:0): FS size: 39616512 bytes (37 MiB, 312 LEBs), max 322 LEBs, journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 11.120000] UBIFS (ubi1:0): reserved for root: 1871185 bytes (1827 KiB)
[ 11.130000] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID C8AD6E3E-8929-45DD-9034-4515EF9942B0, small LPT model
[ 11.140000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 11.160000] block: extroot: not configured
[ 11.160000] UBIFS (ubi1:0): un-mount UBI device 1
[ 11.170000] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" stops
[ 11.180000] UBIFS (ubi1:0): Mounting in unauthenticated mode
[ 11.180000] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 190
[ 11.300000] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[ 11.310000] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.320000] UBIFS (ubi1:0): FS size: 39616512 bytes (37 MiB, 312 LEBs), max 322 LEBs, journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 11.330000] UBIFS (ubi1:0): reserved for root: 1871185 bytes (1827 KiB)
[ 11.340000] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID C8AD6E3E-8929-45DD-9034-4515EF9942B0, small LPT model
[ 11.430000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 11.440000] block: extroot: not configured
[ 11.450000] mount_root: switching to ubifs overlay
[ 11.600000] Root filesystem mounted
[ 13.860000] urandom-seed: Seeding with /etc/urandom.seed
[ 13.950000] procd: - watchdog -
[ 13.970000] procd: - ubus -
[ 14.060000] procd: - init -
Please press Enter to activate this console.
[ 17.660000] kmodloader: loading kernel modules from /etc/modules.d/*
[ 17.710000] tun: Universal TUN/TAP device driver, 1.6
[ 17.880000] atmel_usba_udc 500000.gadget: MMIO registers at [mem 0xf8030000-0xf8033fff] mapped at a001040b
[ 17.890000] atmel_usba_udc 500000.gadget: FIFO at [mem 0x00500000-0x005fffff] mapped at 52fc3313
[ 17.920000] usbcore: registered new interface driver cdc_wdm
[ 18.010000] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 18.280000] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 18.290000] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 18.300000] cfg80211: failed to load regulatory.db
[ 18.310000] cryptodev: loading out-of-tree module taints kernel.
[ 18.330000] cryptodev: driver 1.12 loaded.
[ 18.350000] gre: GRE over IPv4 demultiplexor driver
[ 18.540000] PPTP driver version 0.8.5
[ 18.680000] xt_time: kernel timezone is +0300
[ 18.690000] usbcore: registered new interface driver cdc_ether
[ 18.710000] usbcore: registered new interface driver cdc_ncm
[ 18.790000] usbcore: registered new interface driver qmi_wwan
[ 18.860000] usbcore: registered new interface driver cdc_mbim
[ 18.900000] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 25.260000] Cgroup memory moving (move_charge_at_immigrate) is deprecated. Please report your usecase to linux-mm@kvack.org if you depend on this functionality.
[ 29.490000] udevd[1131]: starting version 3.2.10
[ 29.820000] udevd[1131]: starting eudev-3.2.10
[ 61.010000] macb f0028000.ethernet eth0: configuring for fixed/rgmii link mode
[ 61.020000] macb f0028000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 61.030000] device eth0 entered promiscuous mode
[ 61.060000] ksz9477-switch spi1.0 sw1p1: configuring for phy/gmii link mode
[ 61.070000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 61.080000] br-lan: port 1(sw1p1) entered blocking state
[ 61.090000] br-lan: port 1(sw1p1) entered disabled state
[ 61.120000] ksz9477-switch spi1.0 sw1p1: Link is Up - 1Gbps/Full - flow control off
[ 61.150000] device sw1p1 entered promiscuous mode
[ 61.200000] br-lan: port 1(sw1p1) entered blocking state
[ 61.250000] ksz9477-switch spi1.0 sw1p2: configuring for phy/gmii link mode
[ 61.290000] br-lan: port 2(sw1p2) entered blocking state
[ 61.290000] br-lan: port 2(sw1p2) entered disabled state
[ 61.330000] device sw1p2 entered promiscuous mode
[ 61.410000] ksz9477-switch spi1.0 sw1p3: configuring for phy/gmii link mode
[ 61.450000] br-lan: port 3(sw1p3) entered blocking state
[ 61.450000] br-lan: port 3(sw1p3) entered disabled state
[ 61.530000] device sw1p3 entered promiscuous mode
[ 61.600000] ksz9477-switch spi1.0 sw1p4: configuring for phy/gmii link mode
[ 61.640000] br-lan: port 4(sw1p4) entered blocking state
[ 61.640000] br-lan: port 4(sw1p4) entered disabled state
[ 61.680000] device sw1p4 entered promiscuous mode
[ 61.720000] ksz9477-switch spi1.0 sw1p6: configuring for fixed/ link mode
[ 61.730000] ksz9477-switch spi1.0 sw1p6: Link is Up - 1Gbps/Full - flow control off
[ 61.760000] br-lan: port 5(sw1p6) entered blocking state
[ 61.760000] br-lan: port 5(sw1p6) entered disabled state
[ 61.790000] device sw1p6 entered promiscuous mode
[ 61.800000] br-lan: port 5(sw1p6) entered blocking state
[ 61.940000] ksz9477-switch spi1.0 sw1p5: configuring for phy/gmii link mode
[ 62.160000] ksz9477-switch spi1.0 sw1p1: Link is Down
[ 62.160000] br-lan: port 1(sw1p1) entered disabled state
[ 64.240000] ksz9477-switch spi1.0 sw1p1: Link is Up - 1Gbps/Full - flow control off
[ 64.240000] br-lan: port 1(sw1p1) entered blocking state
[ 66.430000] br-lan: port 1(sw1p1) entered blocking state
[ 66.520000] br-lan: port 5(sw1p6) entered blocking state
[ 68.700000] br-lan: port 1(sw1p1) entered learning state
[ 68.700000] br-lan: port 1(sw1p1) entered forwarding state
[ 68.710000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 68.770000] br-lan: port 5(sw1p6) entered learning state
[ 68.770000] br-lan: port 5(sw1p6) entered forwarding state
[ 87.450000] using random self ethernet address
[ 87.450000] using random host ethernet address
[ 87.460000] usb0: HOST MAC ce:18:97:10:3a:8a
[ 87.460000] usb0: MAC b6:e4:27:ae:b1:a6
[ 87.460000] using random self ethernet address
[ 87.470000] using random host ethernet address
[ 87.470000] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[ 87.480000] g_ether gadget: g_ether ready
tanowrt login: root
Password:
_______ __ __ _
|__ __| \ \ / / | | Embedded Linux Distribution
| | __ _ _ __ __\ \ /\ / / __| |_ by Tano Systems
| |/ _` | '_ \ / _ \ \/ \/ / '__| __|
| | (_| | | | | (_) \ /\ /| | | |_ (c) 2018-2024 Tano Systems LLC
|_|\__,_|_| |_|\___/ \/ \/ |_| \__| https://tano-systems.com
Board: Microchip EVB-KSZ9477 (NAND)
Release: Kirkstone
Revision: 30f32be34959042d70884ae8df562f41cd687826
2024-04-12 08:06:39 UTC
[root@tanowrt ~]#
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.105-rt61-tano-mchp-rt-g22ed83424b-tano0.2.2.20.0.2 (oe-user@oe-host) (arm-oe-linux-gnueabi-gcc (GCC) 11.4.0, GNU ld (GNU Binutils) 2.38.20220708) #1 PREEMPT_RT Fri Apr 14 11:46:12 UTC 2023
[ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Microchip EVB-KSZ9477
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x2f000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000020000000-0x000000002fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000020000000-0x000000002fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000002fffffff]
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 ubi.mtd=system_a,2048 ubi.mtd=rootfs_data,2048 ubi.block=0,rootfs root=/dev/ubiblock0_1 ro rootfstype=squashfs rootwait rootfs_partition=system_a rootfs_volume=rootfs earlyprintk panic=15
[ 0.000000] Unknown kernel command line parameters "earlyprintk rootfs_partition=system_a rootfs_volume=rootfs", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 229068K/262144K available (9216K kernel code, 473K rwdata, 2212K rodata, 1024K init, 165K bss, 16692K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms.
[ 0.000000] rcu: RCU_SOFTIRQ processing moved to rcuc kthreads.
[ 0.000000] No expedited grace period (rcu_normal_after_boot).
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: pit: mask: 0xfffffff max_cycles: 0xfffffff, max_idle_ns: 14479245754 ns
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns
[ 0.000000] Calibrating delay loop... 351.43 BogoMIPS (lpj=1757184)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.060000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.060000] CPU: Testing write buffer coherency: ok
[ 0.060000] Setting up static identity map for 0x20100000 - 0x20100060
[ 0.060000] rcu: Hierarchical SRCU implementation.
[ 0.060000] devtmpfs: initialized
[ 0.090000] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 0.090000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.090000] futex hash table entries: 256 (order: 0, 6144 bytes, linear)
[ 0.100000] pinctrl core: initialized pinctrl subsystem
[ 0.100000] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.100000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.110000] cpuidle: using governor menu
[ 0.160000] AT91: PM: standby: standby, suspend: ulp0
[ 0.160000] gpio-at91 fffff200.gpio: at address (ptrval)
[ 0.170000] gpio-at91 fffff400.gpio: at address (ptrval)
[ 0.170000] gpio-at91 fffff600.gpio: at address (ptrval)
[ 0.170000] gpio-at91 fffff800.gpio: at address (ptrval)
[ 0.170000] gpio-at91 fffffa00.gpio: at address (ptrval)
[ 0.170000] pinctrl-at91 ahb:apb:pinctrl@fffff200: initialized AT91 pinctrl driver
[ 0.230000] at_hdmac ffffe600.dma-controller: Atmel AHB DMA Controller ( cpy set slave ), 8 channels
[ 0.230000] at_hdmac ffffe800.dma-controller: Atmel AHB DMA Controller ( cpy set slave ), 8 channels
[ 0.240000] AT91: Detected SoC family: sama5d3
[ 0.240000] AT91: Detected SoC: sama5d36, revision 2
[ 0.240000] SCSI subsystem initialized
[ 0.240000] usbcore: registered new interface driver usbfs
[ 0.240000] usbcore: registered new interface driver hub
[ 0.240000] usbcore: registered new device driver usb
[ 0.240000] at91_i2c f0014000.i2c: using dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers
[ 0.240000] i2c i2c-0: using pinctrl states for GPIO recovery
[ 0.240000] i2c i2c-0: using generic GPIOs for recovery
[ 0.240000] at91_i2c f0014000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.250000] at91_i2c f0018000.i2c: using dma0chan2 (tx) and dma0chan3 (rx) for DMA transfers
[ 0.250000] i2c i2c-1: using pinctrl states for GPIO recovery
[ 0.250000] i2c i2c-1: using generic GPIOs for recovery
[ 0.250000] at91_i2c f0018000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.250000] at91_i2c f801c000.i2c: can't get DMA channel, continue without DMA support
[ 0.250000] i2c i2c-2: using pinctrl states for GPIO recovery
[ 0.250000] i2c i2c-2: using generic GPIOs for recovery
[ 0.250000] at91_i2c f801c000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.250000] mc: Linux media interface: v0.10
[ 0.250000] videodev: Linux video capture interface: v2.00
[ 0.250000] pps_core: LinuxPPS API ver. 1 registered
[ 0.250000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.250000] PTP clock support registered
[ 0.250000] Advanced Linux Sound Architecture Driver Initialized.
[ 0.250000] Bluetooth: Core ver 2.22
[ 0.250000] NET: Registered PF_BLUETOOTH protocol family
[ 0.250000] Bluetooth: HCI device and connection manager initialized
[ 0.250000] Bluetooth: HCI socket layer initialized
[ 0.250000] Bluetooth: L2CAP socket layer initialized
[ 0.250000] Bluetooth: SCO socket layer initialized
[ 0.260000] clocksource: Switched to clocksource pit
[ 0.290000] NET: Registered PF_INET protocol family
[ 0.290000] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.300000] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 5120 bytes, linear)
[ 0.300000] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.300000] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.300000] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.300000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.300000] UDP hash table entries: 256 (order: 1, 12288 bytes, linear)
[ 0.300000] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes, linear)
[ 0.300000] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.300000] RPC: Registered named UNIX socket transport module.
[ 0.300000] RPC: Registered udp transport module.
[ 0.300000] RPC: Registered tcp transport module.
[ 0.300000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.300000] Initialise system trusted keyrings
[ 0.300000] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.330000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.540000] Key type asymmetric registered
[ 0.540000] Asymmetric key parser 'x509' registered
[ 0.540000] io scheduler mq-deadline registered
[ 0.540000] io scheduler kyber registered
[ 0.570000] brd: module loaded
[ 0.590000] loop: module loaded
[ 0.590000] atmel_usart_serial.0.auto: ttyS1 at MMIO 0xf001c000 (irq = 23, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.600000] atmel_usart_serial.1.auto: ttyS2 at MMIO 0xf0020000 (irq = 24, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.600000] atmel_usart_serial.2.auto: ttyS5 at MMIO 0xf0024000 (irq = 25, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.600000] atmel_usart_serial.3.auto: ttyS0 at MMIO 0xffffee00 (irq = 38, base_baud = 8250000) is a ATMEL_SERIAL
[ 0.600000] printk: console [ttyS0] enabled
[ 0.610000] atmel_spi f0004000.spi: Using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers
[ 0.610000] atmel_spi f0004000.spi: Atmel SPI Controller version 0x213 at 0xf0004000 (irq 19)
[ 0.610000] atmel_spi f8008000.spi: Using dma1chan0 (tx) and dma1chan1 (rx) for DMA transfers
[ 0.610000] ksz9477@0 enforce active low on chipselect handle
[ 0.620000] atmel_spi f8008000.spi: Atmel SPI Controller version 0x213 at 0xf8008000 (irq 28)
[ 0.620000] CAN device driver interface
[ 0.620000] ksz9477-switch spi1.0: Microchip KSZ switch driver version 0.9.0
[ 0.620000] ksz9477-switch spi1.0: Microchip KSZ9477 Switch (7 ports)
[ 0.620000] ksz9477-switch spi1.0: Failed to register DSA switch (-517)
[ 1.280000] macb f0028000.ethernet eth0: Cadence GEM rev 0x00020119 at 0xf0028000 irq 46 (00:10:a1:98:97:01)
[ 1.280000] PPP generic driver version 2.4.2
[ 1.280000] PPP MPPE Compression module registered
[ 1.280000] NET: Registered PF_PPPOX protocol family
[ 1.280000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.280000] ehci-atmel: EHCI Atmel driver
[ 1.280000] atmel-ehci 700000.ehci: EHCI Host Controller
[ 1.280000] atmel-ehci 700000.ehci: new USB bus registered, assigned bus number 1
[ 1.280000] atmel-ehci 700000.ehci: irq 49, io mem 0x00700000
[ 1.310000] atmel-ehci 700000.ehci: USB 2.0 started, EHCI 1.00
[ 1.310000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[ 1.310000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.310000] usb usb1: Product: EHCI Host Controller
[ 1.310000] usb usb1: Manufacturer: Linux 5.15.105-rt61-tano-mchp-rt-g22ed83424b-tano0.2.2.20.0.2 ehci_hcd
[ 1.310000] usb usb1: SerialNumber: 700000.ehci
[ 1.310000] hub 1-0:1.0: USB hub found
[ 1.310000] hub 1-0:1.0: 3 ports detected
[ 1.310000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.310000] ohci-atmel: OHCI Atmel driver
[ 1.310000] at91_ohci 600000.ohci: USB Host Controller
[ 1.310000] at91_ohci 600000.ohci: new USB bus registered, assigned bus number 2
[ 1.310000] at91_ohci 600000.ohci: irq 49, io mem 0x00600000
[ 1.380000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.15
[ 1.380000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.380000] usb usb2: Product: USB Host Controller
[ 1.380000] usb usb2: Manufacturer: Linux 5.15.105-rt61-tano-mchp-rt-g22ed83424b-tano0.2.2.20.0.2 ohci_hcd
[ 1.380000] usb usb2: SerialNumber: at91
[ 1.380000] hub 2-0:1.0: USB hub found
[ 1.380000] hub 2-0:1.0: 3 ports detected
[ 1.390000] usbcore: registered new interface driver cdc_acm
[ 1.390000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.390000] usbcore: registered new interface driver usb-storage
[ 1.390000] usbcore: registered new interface driver usbserial_generic
[ 1.390000] usbserial: USB Serial support registered for generic
[ 1.390000] usbcore: registered new interface driver ftdi_sio
[ 1.390000] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 1.390000] at91_rtc fffffeb0.rtc: registered as rtc0
[ 1.390000] at91_rtc fffffeb0.rtc: setting system clock to 2024-04-12T12:05:43 UTC (1712923543)
[ 1.390000] at91_rtc fffffeb0.rtc: AT91 Real Time Clock driver.
[ 1.390000] i2c_dev: i2c /dev entries driver
[ 1.390000] at91-reset fffffe00.rstc: Starting after software reset
[ 1.400000] at91_wdt fffffe40.watchdog: watchdog already configured differently (mr = 1fff2eff expecting 1fff2fff)
[ 1.400000] at91sam9_wdt: enabled (heartbeat=15 sec, nowayout=0)
[ 1.400000] Bluetooth: HCI UART driver ver 2.3
[ 1.400000] Bluetooth: HCI UART protocol H4 registered
[ 1.400000] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 1.400000] usbcore: registered new interface driver btusb
[ 1.400000] sdhci: Secure Digital Host Controller Interface driver
[ 1.400000] sdhci: Copyright(c) Pierre Ossman
[ 1.400000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.400000] atmel_aes f8038000.crypto: version: 0x135
[ 1.410000] atmel_mci f0000000.mmc: version: 0x505
[ 1.410000] atmel_mci f0000000.mmc: using dma0chan6 for DMA transfers
[ 1.410000] atmel_mci f8000000.mmc: version: 0x505
[ 1.410000] atmel_mci f8000000.mmc: using dma1chan4 for DMA transfers
[ 1.410000] atmel_aes f8038000.crypto: Atmel AES - Using dma1chan2, dma1chan3 for DMA transfers
[ 1.420000] atmel_sha f8034000.crypto: version: 0x410
[ 1.420000] atmel_sha f8034000.crypto: using dma1chan5 for DMA transfers
[ 1.420000] atmel_sha f8034000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512
[ 1.420000] atmel_tdes f803c000.crypto: version: 0x701
[ 1.420000] atmel_tdes f803c000.crypto: using dma1chan6, dma1chan7 for DMA transfers
[ 1.430000] atmel_tdes f803c000.crypto: Atmel DES/TDES
[ 1.430000] usbcore: registered new interface driver usbhid
[ 1.430000] usbhid: USB HID core driver
[ 1.430000] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.430000] nand: Micron MT29F2G08ABAEAWP
[ 1.430000] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.430000] Bad block table found at page 131008, version 0x01
[ 1.440000] Bad block table found at page 130944, version 0x01
[ 1.440000] 7 fixed-partitions partitions found on MTD device atmel_nand
[ 1.440000] Creating 7 MTD partitions on "atmel_nand":
[ 1.440000] 0x000000000000-0x000000040000 : "at91bootstrap"
[ 1.440000] 0x000000040000-0x000000180000 : "uboot"
[ 1.450000] 0x000000180000-0x0000001c0000 : "startup"
[ 1.450000] 0x0000001c0000-0x000000200000 : "ubootenv"
[ 1.460000] atmel_mci f8000000.mmc: Atmel MCI controller at 0xf8000000 irq 27, 1 slots
[ 1.460000] atmel_mci f0000000.mmc: Atmel MCI controller at 0xf0000000 irq 18, 1 slots
[ 1.460000] 0x000000200000-0x000006a00000 : "system_a"
[ 1.470000] 0x000006a00000-0x00000d200000 : "system_b"
[ 1.470000] 0x00000d200000-0x000010000000 : "rootfs_data"
[ 1.480000] iio iio:device0: Resolution used: 12 bits
[ 1.480000] iio iio:device0: ADC Touch screen is disabled.
[ 1.490000] u32 classifier
[ 1.490000] input device check on
[ 1.490000] Actions configured
[ 1.490000] NET: Registered PF_INET6 protocol family
[ 1.490000] Segment Routing with IPv6
[ 1.490000] In-situ OAM (IOAM) with IPv6
[ 1.490000] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 1.500000] NET: Registered PF_PACKET protocol family
[ 1.500000] Bridge firewalling registered
[ 1.500000] can: controller area network core
[ 1.500000] NET: Registered PF_CAN protocol family
[ 1.500000] can: raw protocol
[ 1.500000] can: broadcast manager protocol
[ 1.500000] can: netlink gateway - max_hops=1
[ 1.500000] Bluetooth: RFCOMM TTY layer initialized
[ 1.500000] Bluetooth: RFCOMM socket layer initialized
[ 1.500000] Bluetooth: RFCOMM ver 1.11
[ 1.500000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.500000] Bluetooth: BNEP filters: protocol multicast
[ 1.500000] Bluetooth: BNEP socket layer initialized
[ 1.500000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.500000] Bluetooth: HIDP socket layer initialized
[ 1.500000] l2tp_core: L2TP core driver, V2.0
[ 1.500000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.500000] l2tp_netlink: L2TP netlink interface
[ 1.500000] printk: console [ttyS0]: printing thread started
[ 1.500000] Loading compiled-in X.509 certificates
[ 1.540000] ksz9477-switch spi1.0: Microchip KSZ switch driver version 0.9.0
[ 1.610000] ksz9477-switch spi1.0: Microchip KSZ9477 Switch (7 ports)
[ 1.610000] ksz9477-switch spi1.0: Use rgmii-txid
[ 1.620000] ksz9477-switch spi1.0: Port 5: Enabled tail tagging
[ 3.090000] ksz9477-switch spi1.0: Enabled jumbo frames support
[ 3.100000] ksz9477-switch spi1.0: The switch has been successfully started
[ 3.140000] ksz9477-switch spi1.0 sw1p1 (uninitialized): PHY [dsa-0.0:00] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 3.140000] ksz9477-switch spi1.0 sw1p2 (uninitialized): PHY [dsa-0.0:01] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 3.140000] ksz9477-switch spi1.0 sw1p3 (uninitialized): PHY [dsa-0.0:02] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 3.180000] ksz9477-switch spi1.0 sw1p4 (uninitialized): PHY [dsa-0.0:03] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 3.190000] ksz9477-switch spi1.0 sw1p5 (uninitialized): PHY [dsa-0.0:04] driver [Microchip KSZ9477 Switch] (irq=POLL)
[ 3.190000] ksz9477-switch spi1.0: Using legacy PHYLIB callbacks. Please migrate to PHYLINK!
[ 3.190000] DSA: tree 0 setup
[ 3.190000] ksz9477-switch spi1.0: User ports mask is 0x5f
[ 3.190000] ksz9477-switch spi1.0: CPU port MAC: 00:10:a1:98:97:01
[ 3.190000] ksz9477-switch spi1.0: Port 0 [sw1p1] MAC: 00:10:a1:98:97:02
[ 3.210000] ksz9477-switch spi1.0: Port 1 [sw1p2] MAC: 00:10:a1:98:97:03
[ 3.210000] ksz9477-switch spi1.0: Port 2 [sw1p3] MAC: 00:10:a1:98:97:04
[ 3.210000] ksz9477-switch spi1.0: Port 3 [sw1p4] MAC: 00:10:a1:98:97:05
[ 3.210000] ksz9477-switch spi1.0: Port 4 [sw1p5] MAC: 00:10:a1:98:97:06
[ 3.210000] ksz9477-switch spi1.0: Port 6 [sw1p6] MAC: 00:10:a1:98:97:07
[ 3.210000] ksz9477-switch spi1.0: Port mask: 0x7f, CPU mask: 0x20, DSA mask: 0x0, user mask: 0x5f
[ 3.210000] ksz9477-switch spi1.0: Port 0 [USER]: sw1p1
[ 3.210000] ksz9477-switch spi1.0: Port 1 [USER]: sw1p2
[ 3.210000] ksz9477-switch spi1.0: Port 2 [USER]: sw1p3
[ 3.210000] ksz9477-switch spi1.0: Port 3 [USER]: sw1p4
[ 3.210000] ksz9477-switch spi1.0: Port 4 [USER]: sw1p5
[ 3.210000] ksz9477-switch spi1.0: Port 5 [CPU]: eth0
[ 3.210000] ksz9477-switch spi1.0: Port 6 [USER]: sw1p6
[ 3.210000] ksz9477-switch spi1.0: DSA switch registered
[ 3.210000] ksz9477-switch spi1.0: Created sysfs entries
[ 3.210000] ubi0: default fastmap pool size: 40
[ 3.210000] ubi0: default fastmap WL pool size: 20
[ 3.210000] ubi0: attaching mtd4
[ 4.010000] ubi0: scanning is finished
[ 4.030000] ubi0: attached mtd4 (name "system_a", size 104 MiB)
[ 4.030000] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.030000] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.030000] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.030000] ubi0: good PEBs: 832, bad PEBs: 0, corrupted PEBs: 0
[ 4.030000] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 4.030000] ubi0: max/mean erase counter: 32/25, WL threshold: 4096, image sequence number: 345045444
[ 4.030000] ubi0: available PEBs: 538, total reserved PEBs: 294, PEBs reserved for bad PEB handling: 40
[ 4.030000] ubi1: default fastmap pool size: 15
[ 4.030000] ubi1: default fastmap WL pool size: 7
[ 4.030000] ubi1: attaching mtd6
[ 4.030000] ubi0: background thread "ubi_bgt0d" started, PID 128
[ 4.420000] ubi1: scanning is finished
[ 4.430000] ubi1: attached mtd6 (name "rootfs_data", size 46 MiB)
[ 4.430000] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.430000] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.430000] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.430000] ubi1: good PEBs: 364, bad PEBs: 4, corrupted PEBs: 0
[ 4.430000] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 4.430000] ubi1: max/mean erase counter: 51/26, WL threshold: 4096, image sequence number: 814988759
[ 4.430000] ubi1: available PEBs: 0, total reserved PEBs: 364, PEBs reserved for bad PEB handling: 36
[ 4.450000] ubi1: background thread "ubi_bgt1d" started, PID 129
[ 4.460000] block ubiblock0_1: created from ubi0:1(rootfs)
[ 4.460000] ALSA device list:
[ 4.460000] No soundcards found.
[ 4.470000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 4.470000] devtmpfs: mounted
[ 4.490000] Freeing unused kernel image (initmem) memory: 1024K
[ 4.520000] Run /sbin/init as init process
[ 4.910000] init: Console is alive
[ 4.910000] init: - watchdog -
[ 6.100000] random: crng init done
[ 6.480000] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.520000] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.530000] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 11.140000] SWUPDATE: AT91Bootstrap version 4.0.8-gitAUTOINC+c331a16179-r0.tano3.3
[ 11.610000] SWUPDATE: U-Boot version 2023.07.02-gitAUTOINC+842d9d53a1-tano0.3
[ 11.730000] SWUPDATE: U-Boot startup version 1.0.0-tano1.atmel1
[ 11.770000] SWUPDATE: Kernel version 5.15.105-rt61-tano-mchp-rt-g22ed83424b-tano0.2.2.20.0.2
[ 11.810000] SWUPDATE: Read-only filesystem version 2024-04-12-08-40-02-UTC
[ 12.240000] mount_root: loading kmods from internal overlay
[ 12.640000] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 12.660000] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 12.830000] UBIFS (ubi1:0): Mounting in unauthenticated mode
[ 12.830000] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 217
[ 12.900000] UBIFS (ubi1:0): recovery needed
[ 13.030000] UBIFS (ubi1:0): recovery completed
[ 13.030000] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[ 13.030000] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 13.030000] UBIFS (ubi1:0): FS size: 39616512 bytes (37 MiB, 312 LEBs), max 322 LEBs, journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 13.030000] UBIFS (ubi1:0): reserved for root: 1871185 bytes (1827 KiB)
[ 13.030000] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID C8AD6E3E-8929-45DD-9034-4515EF9942B0, small LPT model
[ 13.030000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 13.060000] block: extroot: not configured
[ 13.090000] UBIFS (ubi1:0): un-mount UBI device 1
[ 13.090000] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" stops
[ 13.120000] UBIFS (ubi1:0): Mounting in unauthenticated mode
[ 13.120000] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 218
[ 13.270000] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[ 13.270000] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 13.270000] UBIFS (ubi1:0): FS size: 39616512 bytes (37 MiB, 312 LEBs), max 322 LEBs, journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 13.270000] UBIFS (ubi1:0): reserved for root: 1871185 bytes (1827 KiB)
[ 13.270000] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID C8AD6E3E-8929-45DD-9034-4515EF9942B0, small LPT model
[ 13.410000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 13.420000] block: extroot: not configured
[ 13.450000] mount_root: switching to ubifs overlay
[ 13.650000] Root filesystem mounted
[ 16.390000] urandom-seed: Seeding with /etc/urandom.seed
[ 16.500000] procd: - watchdog -
[ 16.520000] procd: - ubus -
[ 16.710000] procd: - init -
Please press Enter to activate this console.
[ 21.160000] kmodloader: loading kernel modules from /etc/modules.d/*
[ 21.210000] tun: Universal TUN/TAP device driver, 1.6
[ 21.410000] atmel_usba_udc 500000.gadget: MMIO registers at [mem 0xf8030000-0xf8033fff] mapped at 79ebcc66
[ 21.410000] atmel_usba_udc 500000.gadget: FIFO at [mem 0x00500000-0x005fffff] mapped at b9fc0435
[ 21.460000] usbcore: registered new interface driver cdc_wdm
[ 21.570000] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 21.890000] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 21.890000] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 21.890000] cfg80211: failed to load regulatory.db
[ 21.890000] cryptodev: loading out-of-tree module taints kernel.
[ 21.930000] cryptodev: driver 1.12 loaded.
[ 21.930000] gre: GRE over IPv4 demultiplexor driver
[ 22.220000] PPTP driver version 0.8.5
[ 22.380000] xt_time: kernel timezone is +0300
[ 22.400000] usbcore: registered new interface driver cdc_ether
[ 22.400000] usbcore: registered new interface driver cdc_ncm
[ 22.500000] usbcore: registered new interface driver qmi_wwan
[ 22.560000] usbcore: registered new interface driver cdc_mbim
[ 22.570000] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 30.070000] Cgroup memory moving (move_charge_at_immigrate) is deprecated. Please report your usecase to linux-mm@kvack.org if you depend on this functionality.
[ 35.460000] udevd[1160]: starting version 3.2.10
[ 35.960000] udevd[1160]: starting eudev-3.2.10
[ 73.560000] macb f0028000.ethernet eth0: configuring for fixed/rgmii link mode
[ 73.560000] macb f0028000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 73.620000] device eth0 entered promiscuous mode
[ 74.770000] ksz9477-switch spi1.0 sw1p1: configuring for phy/gmii link mode
[ 74.790000] ksz9477-switch spi1.0 sw1p1: Link is Up - 1Gbps/Full - flow control off
[ 74.790000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 74.790000] br-lan: port 1(sw1p1) entered blocking state
[ 74.790000] br-lan: port 1(sw1p1) entered disabled state
[ 75.950000] device sw1p1 entered promiscuous mode
[ 76.360000] br-lan: port 1(sw1p1) entered blocking state
[ 78.000000] ksz9477-switch spi1.0 sw1p2: configuring for phy/gmii link mode
[ 78.000000] br-lan: port 2(sw1p2) entered blocking state
[ 78.000000] br-lan: port 2(sw1p2) entered disabled state
[ 78.860000] device sw1p2 entered promiscuous mode
[ 78.870000] br-lan: port 1(sw1p1) entered blocking state
[ 80.390000] ksz9477-switch spi1.0 sw1p3: configuring for phy/gmii link mode
[ 80.420000] br-lan: port 3(sw1p3) entered blocking state
[ 80.420000] br-lan: port 3(sw1p3) entered disabled state
[ 80.950000] device sw1p3 entered promiscuous mode
[ 80.960000] br-lan: port 1(sw1p1) entered learning state
[ 80.960000] br-lan: port 1(sw1p1) entered forwarding state
[ 80.990000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 82.210000] ksz9477-switch spi1.0 sw1p4: configuring for phy/gmii link mode
[ 82.240000] br-lan: port 4(sw1p4) entered blocking state
[ 82.240000] br-lan: port 4(sw1p4) entered disabled state
[ 82.690000] device sw1p4 entered promiscuous mode
[ 83.110000] ksz9477-switch spi1.0 sw1p6: configuring for fixed/ link mode
[ 83.110000] ksz9477-switch spi1.0 sw1p6: Link is Up - 1Gbps/Full - flow control off
[ 83.320000] br-lan: port 5(sw1p6) entered blocking state
[ 83.320000] br-lan: port 5(sw1p6) entered disabled state
[ 84.280000] device sw1p6 entered promiscuous mode
[ 84.280000] br-lan: port 5(sw1p6) entered blocking state
[ 85.600000] ksz9477-switch spi1.0 sw1p5: configuring for phy/gmii link mode
[ 85.630000] br-lan: port 5(sw1p6) entered blocking state
[ 85.650000] br-lan: port 5(sw1p6) entered learning state
[ 85.650000] br-lan: port 5(sw1p6) entered forwarding state
[ 100.300000] using random self ethernet address
[ 100.300000] using random host ethernet address
[ 100.300000] usb0: HOST MAC fe:cb:8d:20:44:2f
[ 100.300000] usb0: MAC ae:ba:b9:aa:b2:97
[ 100.340000] using random self ethernet address
[ 100.340000] using random host ethernet address
[ 100.340000] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[ 100.340000] g_ether gadget: g_ether ready
tanowrt login: root
Password:
_______ __ __ _
|__ __| \ \ / / | | Embedded Linux Distribution
| | __ _ _ __ __\ \ /\ / / __| |_ by Tano Systems
| |/ _` | '_ \ / _ \ \/ \/ / '__| __|
| | (_| | | | | (_) \ /\ /| | | |_ (c) 2018-2024 Tano Systems LLC
|_|\__,_|_| |_|\___/ \/ \/ |_| \__| https://tano-systems.com
Board: Microchip EVB-KSZ9477 (NAND)
Release: Kirkstone
Revision: 30f32be34959042d70884ae8df562f41cd687826
2024-04-12 08:40:02 UTC
[root@tanowrt ~]#