2.12.2 SAMA5D3 Xplained Booting from Internal NAND Flash Logs

2.12.2.1 AT91Bootstrap

AT91Bootstrap 4.0.8-gitAUTOINC+c331a16179-r0.tano3.3 (2023-12-18 09:57:32)

NAND: ONFI flash detected
NAND: Manufacturer ID: 0x2c Chip ID: 0xda
NAND: Page Bytes: 2048, Spare Bytes: 64
NAND: ECC Correctability Bits: 4, ECC Sector Bytes: 512
NAND: Disable On-Die ECC
NAND: Initialize PMECC params, cap: 4, sector: 512
NAND: Image: Copy 0x100000 bytes from 0x40000 to 0x26f00000
NAND: Done to load image
<debug_uart>

2.12.2.2 U-Boot

U-Boot 2023.07.02-gitAUTOINC+842d9d53a1-tano0.3 (Dec 18 2023 - 10:10:05 +0000)

CPU: SAMA5D36
Crystal frequency:       12 MHz
CPU clock        :      528 MHz
Master clock     :      132 MHz
DRAM:  256 MiB
Core:  209 devices, 20 uclasses, devicetree: separate
sorry, watchdog is disabled
WDT:   Failed to start watchdog@fffffe40
NAND:  256 MiB
MMC:   Atmel mci: 0, Atmel mci: 1
Loading Environment from NAND... OK
In:    serial@ffffee00
Out:   serial@ffffee00
Err:   serial@ffffee00
Net:   
Warning: ethernet@f0028000 MAC addresses don't match:
Address in ROM is00:10:a1:98:97:02
Address in environment is00:10:a1:98:97:01
eth0: ethernet@f0028000, eth1: ethernet@f802c000
Hit any key to stop autoboot:  3  2  1  0 

NAND read: device 0 offset 0x180000, size 0x40000
 262144 bytes read: OK
## Executing script at 21000000
Board name: sama5d3_xplained
Active system A
Loading kernel fitImage...
ubi0: attaching mtd5
ubi0: scanning is finished
ubi0: attached mtd5 (name "system_a", size 104 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 832, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 7/3, WL threshold: 4096, image sequence number: 535480031
ubi0: available PEBs: 541, total reserved PEBs: 291, PEBs reserved for bad PEB handling: 40
No size specified -> Using max size (6094848)
Read 6094848 bytes from volume kernel to 24000000
Booting kernel 0x24000000#conf-at91-sama5d3_xplained.dtb...
## Loading kernel from FIT Image at 24000000 ...
   Using 'conf-at91-sama5d3_xplained.dtb' configuration
   Trying 'kernel-1' kernel subimage
     Description:  Linux kernel
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x24000118
     Data Size:    6039872 Bytes = 5.8 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x22000000
     Entry Point:  0x22000000
     Hash algo:    sha256
     Hash value:   5270cd1c1ed37581683a7104485043f18e1b6914bad94b7470e57b8cd7a54bb3
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 24000000 ...
   Using 'conf-at91-sama5d3_xplained.dtb' configuration
   Trying 'fdt-at91-sama5d3_xplained.dtb' fdt subimage
     Description:  Flattened Device Tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x245c2b70
     Data Size:    40610 Bytes = 39.7 KiB
     Architecture: ARM
     Load Address: 0x23e00000
     Hash algo:    sha256
     Hash value:   03d4ddbb3f99d5196f2cd499ec7f22068e9b32e0848cf6fca75af26d75bc5472
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x245c2b70 to 0x23e00000
   Booting using the fdt blob at 0x23e00000
Working FDT set to 23e00000
   Loading Kernel Image
   Loading Device Tree to 2eb15000, end 2eb21ea1 ... OK
Working FDT set to 2eb15000

Starting kernel ...

2.12.2.3 Linux Kernel (OS)

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.1.20.0.1 (oe-user@oe-host) (arm-oe-linux-gnueabi-gcc (GCC) 11.4.0, GNU ld (GNU Binutils) 2.38.20220708) #1 Tue Jan 23 16:07:43 UTC 2024
[    0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: SAMA5D3 Xplained
[    0.000000] Memory policy: Data cache writeback
[    0.000000] cma: Reserved 16 MiB at 0x2e800000
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000020000000-0x000000002fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000020000000-0x000000002fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000002fffffff]
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: console=ttyS0,115200n8  ubi.mtd=system_a,2048 ubi.mtd=rootfs_data,2048 ubi.block=0,rootfs root=/dev/ubiblock0_1 ro rootfstype=squashfs rootwait rootfs_partition=system_a rootfs_volume=rootfs earlyprintk panic=15
[    0.000000] Unknown kernel command line parameters "earlyprintk rootfs_partition=system_a rootfs_volume=rootfs", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 229084K/262144K available (9216K kernel code, 461K rwdata, 2336K rodata, 1024K init, 168K bss, 16676K reserved, 16384K cma-reserved)
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: timer@f0010000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 115833966437 ns
[    0.000004] sched_clock: 32 bits at 17MHz, resolution 60ns, wraps every 130150523873ns
[    0.000043] Switching to timer-based delay loop, resolution 60ns
[    0.000471] clocksource: pit: mask: 0xfffffff max_cycles: 0xfffffff, max_idle_ns: 14479245754 ns
[    0.001179] Console: colour dummy device 80x30
[    0.001269] Calibrating delay loop (skipped), value calculated using timer frequency.. 33.00 BogoMIPS (lpj=165000)
[    0.001308] CPU: Testing write buffer coherency: ok
[    0.001398] pid_max: default: 32768 minimum: 301
[    0.001833] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001886] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.005727] Setting up static identity map for 0x20100000 - 0x20100060
[    0.007151] devtmpfs: initialized
[    0.022670] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[    0.023192] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.023247] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.025481] pinctrl core: initialized pinctrl subsystem
[    0.028494] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.030913] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.033705] cpuidle: using governor menu
[    0.067066] AT91: PM: standby: standby, suspend: ulp0
[    0.068877] gpio-at91 fffff200.gpio: at address (ptrval)
[    0.070662] gpio-at91 fffff400.gpio: at address (ptrval)
[    0.072525] gpio-at91 fffff600.gpio: at address (ptrval)
[    0.074471] gpio-at91 fffff800.gpio: at address (ptrval)
[    0.076531] gpio-at91 fffffa00.gpio: at address (ptrval)
[    0.078537] pinctrl-at91 ahb:apb:pinctrl@fffff200: initialized AT91 pinctrl driver
[    0.105093] at_hdmac ffffe600.dma-controller: Atmel AHB DMA Controller ( cpy set slave ), 8 channels
[    0.107330] at_hdmac ffffe800.dma-controller: Atmel AHB DMA Controller ( cpy set slave ), 8 channels
[    0.110396] AT91: Detected SoC family: sama5d3
[    0.110419] AT91: Detected SoC: sama5d36, revision 2
[    0.112700] SCSI subsystem initialized
[    0.113370] usbcore: registered new interface driver usbfs
[    0.113513] usbcore: registered new interface driver hub
[    0.113633] usbcore: registered new device driver usb
[    0.114834] at91_i2c f0014000.i2c: using dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers
[    0.115245] i2c i2c-0: using pinctrl states for GPIO recovery
[    0.115362] i2c i2c-0: using generic GPIOs for recovery
[    0.115504] at91_i2c f0014000.i2c: AT91 i2c bus driver (hw version: 0x402).
[    0.116484] at91_i2c f0018000.i2c: using dma0chan2 (tx) and dma0chan3 (rx) for DMA transfers
[    0.116857] i2c i2c-1: using pinctrl states for GPIO recovery
[    0.116975] i2c i2c-1: using generic GPIOs for recovery
[    0.117119] at91_i2c f0018000.i2c: AT91 i2c bus driver (hw version: 0x402).
[    0.118066] at91_i2c f801c000.i2c: can't get DMA channel, continue without DMA support
[    0.118447] i2c i2c-2: using pinctrl states for GPIO recovery
[    0.118559] i2c i2c-2: using generic GPIOs for recovery
[    0.118699] at91_i2c f801c000.i2c: AT91 i2c bus driver (hw version: 0x402).
[    0.119567] mc: Linux media interface: v0.10
[    0.119745] videodev: Linux video capture interface: v2.00
[    0.119920] pps_core: LinuxPPS API ver. 1 registered
[    0.119935] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.120062] PTP clock support registered
[    0.120806] Advanced Linux Sound Architecture Driver Initialized.
[    0.122098] Bluetooth: Core ver 2.22
[    0.122256] NET: Registered PF_BLUETOOTH protocol family
[    0.122273] Bluetooth: HCI device and connection manager initialized
[    0.122306] Bluetooth: HCI socket layer initialized
[    0.122339] Bluetooth: L2CAP socket layer initialized
[    0.122391] Bluetooth: SCO socket layer initialized
[    0.123873] clocksource: Switched to clocksource timer@f0010000
[    0.156381] NET: Registered PF_INET protocol family
[    0.156855] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.158663] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.158752] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.158796] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.158865] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.158968] TCP: Hash tables configured (established 2048 bind 2048)
[    0.159201] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.159260] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.159648] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.160892] RPC: Registered named UNIX socket transport module.
[    0.160924] RPC: Registered udp transport module.
[    0.160933] RPC: Registered tcp transport module.
[    0.160940] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.162410] Initialise system trusted keyrings
[    0.163838] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    0.164963] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.371858] Key type asymmetric registered
[    0.371892] Asymmetric key parser 'x509' registered
[    0.372053] io scheduler mq-deadline registered
[    0.372081] io scheduler kyber registered
[    0.394826] brd: module loaded
[    0.410671] loop: module loaded
[    0.412330] atmel_usart_serial.0.auto: ttyS1 at MMIO 0xf001c000 (irq = 28, base_baud = 4125000) is a ATMEL_SERIAL
[    0.415133] atmel_usart_serial.1.auto: ttyS2 at MMIO 0xf0020000 (irq = 29, base_baud = 4125000) is a ATMEL_SERIAL
[    0.417775] atmel_usart_serial.2.auto: ttyS5 at MMIO 0xf0024000 (irq = 30, base_baud = 4125000) is a ATMEL_SERIAL
[    0.420456] atmel_usart_serial.3.auto: ttyS0 at MMIO 0xffffee00 (irq = 31, base_baud = 8250000) is a ATMEL_SERIAL
[    1.125190] printk: console [ttyS0] enabled
[    1.135262] atmel_spi f0004000.spi: Using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers
[    1.145003] atmel_spi f0004000.spi: Atmel SPI Controller version 0x213 at 0xf0004000 (irq 32)
[    1.154641] atmel_spi f8008000.spi: Using dma1chan0 (tx) and dma1chan1 (rx) for DMA transfers
[    1.164325] atmel_spi f8008000.spi: Atmel SPI Controller version 0x213 at 0xf8008000 (irq 33)
[    1.176452] CAN device driver interface
[    1.182248] at91_can f000c000.can: device registered (reg_base=(ptrval), irq=34)
[    1.196301] macb f0028000.ethernet eth0: Cadence GEM rev 0x00020119 at 0xf0028000 irq 35 (00:10:a1:98:97:01)
[    1.211580] macb f802c000.ethernet eth1: Cadence MACB rev 0x0001010c at 0xf802c000 irq 36 (00:10:a1:98:97:02)
[    1.222169] PPP generic driver version 2.4.2
[    1.227455] PPP MPPE Compression module registered
[    1.232238] NET: Registered PF_PPPOX protocol family
[    1.241769] atmel-ehci 700000.ehci: EHCI Host Controller
[    1.247214] atmel-ehci 700000.ehci: new USB bus registered, assigned bus number 1
[    1.255314] atmel-ehci 700000.ehci: irq 37, io mem 0x00700000
[    1.283958] atmel-ehci 700000.ehci: USB 2.0 started, EHCI 1.00
[    1.290181] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    1.298525] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.305771] usb usb1: Product: EHCI Host Controller
[    1.310623] usb usb1: Manufacturer: Linux 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.1.20.0.1 ehci_hcd
[    1.320254] usb usb1: SerialNumber: 700000.ehci
[    1.326525] hub 1-0:1.0: USB hub found
[    1.330358] hub 1-0:1.0: 3 ports detected
[    1.338363] at91_ohci 600000.ohci: USB Host Controller
[    1.343559] at91_ohci 600000.ohci: new USB bus registered, assigned bus number 2
[    1.351468] at91_ohci 600000.ohci: irq 37, io mem 0x00600000
[    1.428315] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[    1.436666] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.443931] usb usb2: Product: USB Host Controller
[    1.448690] usb usb2: Manufacturer: Linux 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.1.20.0.1 ohci_hcd
[    1.458327] usb usb2: SerialNumber: at91
[    1.463739] hub 2-0:1.0: USB hub found
[    1.467663] hub 2-0:1.0: 3 ports detected
[    1.473971] usbcore: registered new interface driver cdc_acm
[    1.479626] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.487959] usbcore: registered new interface driver usb-storage
[    1.494289] usbcore: registered new interface driver usbserial_generic
[    1.500873] usbserial: USB Serial support registered for generic
[    1.507022] usbcore: registered new interface driver ftdi_sio
[    1.512820] usbserial: USB Serial support registered for FTDI USB Serial Device
[    1.523270] at91_rtc fffffeb0.rtc: registered as rtc0
[    1.528452] at91_rtc fffffeb0.rtc: setting system clock to 2007-01-01T00:00:12 UTC (1167609612)
[    1.537237] at91_rtc fffffeb0.rtc: AT91 Real Time Clock driver.
[    1.543471] i2c_dev: i2c /dev entries driver
[    1.550904] at91-reset fffffe00.reset-controller: Starting after wakeup
[    1.559466] Bluetooth: HCI UART driver ver 2.3
[    1.563968] Bluetooth: HCI UART protocol H4 registered
[    1.569181] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    1.575653] usbcore: registered new interface driver btusb
[    1.581725] sdhci: Secure Digital Host Controller Interface driver
[    1.587991] sdhci: Copyright(c) Pierre Ossman
[    1.592615] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.600449] ledtrig-cpu: registered to indicate activity on CPUs
[    1.607098] atmel_aes f8038000.crypto: version: 0x135
[    1.612461] atmel_aes f8038000.crypto: Atmel AES - Using dma1chan2, dma1chan3 for DMA transfers
[    1.622118] atmel_sha f8034000.crypto: version: 0x410
[    1.627328] atmel_sha f8034000.crypto: using dma1chan4 for DMA transfers
[    1.634214] atmel_sha f8034000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512
[    1.642223] atmel_tdes f803c000.crypto: version: 0x701
[    1.647632] atmel_tdes f803c000.crypto: using dma1chan5, dma1chan6 for DMA transfers
[    1.655666] atmel_tdes f803c000.crypto: Atmel DES/TDES
[    1.661547] usbcore: registered new interface driver usbhid
[    1.667181] usbhid: USB HID core driver
[    1.675141] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.681497] nand: Micron MT29F2G08ABAEAWP
[    1.685581] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.695209] atmel_mci f0000000.mmc: version: 0x505
[    1.700087] atmel_mci f0000000.mmc: using dma0chan7 for DMA transfers
[    1.709096] atmel_mci f8000000.mmc: version: 0x505
[    1.714071] atmel_mci f8000000.mmc: using dma1chan7 for DMA transfers
[    1.721832] Bad block table found at page 131008, version 0x01
[    1.728538] Bad block table found at page 130944, version 0x01
[    1.734913] atmel_mci f0000000.mmc: Atmel MCI controller at 0xf0000000 irq 43, 1 slots
[    1.744039] 7 fixed-partitions partitions found on MTD device atmel_nand
[    1.750798] Creating 7 MTD partitions on "atmel_nand":
[    1.755981] 0x000000000000-0x000000040000 : "at91bootstrap"
[    1.762180] atmel_mci f8000000.mmc: Atmel MCI controller at 0xf8000000 irq 44, 1 slots
[    1.773847] 0x000000040000-0x000000180000 : "uboot"
[    1.782196] 0x000000180000-0x0000001c0000 : "startup"
[    1.790752] 0x0000001c0000-0x000000200000 : "ubootenv"
[    1.799377] 0x000000200000-0x000006a00000 : "system_a"
[    1.808707] 0x000006a00000-0x00000d200000 : "system_b"
[    1.817961] 0x00000d200000-0x000010000000 : "rootfs_data"
[    1.828692] iio iio:device0: Resolution used: 12 bits
[    1.833741] iio iio:device0: ADC Touch screen is disabled.
[    1.846078] u32 classifier
[    1.848763]     input device check on
[    1.852425]     Actions configured
[    1.856571] NET: Registered PF_INET6 protocol family
[    1.865017] Segment Routing with IPv6
[    1.868806] In-situ OAM (IOAM) with IPv6
[    1.872876] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.880420] NET: Registered PF_PACKET protocol family
[    1.885670] Bridge firewalling registered
[    1.889652] can: controller area network core
[    1.894281] NET: Registered PF_CAN protocol family
[    1.899054] can: raw protocol
[    1.902032] can: broadcast manager protocol
[    1.906299] can: netlink gateway - max_hops=1
[    1.911196] Bluetooth: RFCOMM TTY layer initialized
[    1.916180] Bluetooth: RFCOMM socket layer initialized
[    1.921336] Bluetooth: RFCOMM ver 1.11
[    1.925143] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    1.930431] Bluetooth: BNEP filters: protocol multicast
[    1.935733] Bluetooth: BNEP socket layer initialized
[    1.940670] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.946655] Bluetooth: HIDP socket layer initialized
[    1.951640] l2tp_core: L2TP core driver, V2.0
[    1.956031] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[    1.960785] l2tp_netlink: L2TP netlink interface
[    1.966604] Loading compiled-in X.509 certificates
[    2.007267] ubi0: default fastmap pool size: 40
[    2.011789] ubi0: default fastmap WL pool size: 20
[    2.016666] ubi0: attaching mtd4
[    2.574244] ubi0: scanning is finished
[    2.588332] ubi0: attached mtd4 (name "system_a", size 104 MiB)
[    2.594348] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.601209] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.608081] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.615068] ubi0: good PEBs: 832, bad PEBs: 0, corrupted PEBs: 0
[    2.621054] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    2.628329] ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 1452489365
[    2.637491] ubi0: available PEBs: 539, total reserved PEBs: 293, PEBs reserved for bad PEB handling: 40
[    2.647006] ubi0: background thread "ubi_bgt0d" started, PID 92
[    2.652961] ubi1: default fastmap pool size: 15
[    2.657506] ubi1: default fastmap WL pool size: 7
[    2.662179] ubi1: attaching mtd6
[    2.927683] ubi1: scanning is finished
[    2.940347] ubi1: attached mtd6 (name "rootfs_data", size 46 MiB)
[    2.946532] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.953399] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.960239] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.967233] ubi1: good PEBs: 364, bad PEBs: 4, corrupted PEBs: 0
[    2.973217] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[    2.980494] ubi1: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 863816412
[    2.989567] ubi1: available PEBs: 0, total reserved PEBs: 364, PEBs reserved for bad PEB handling: 36
[    2.999371] ubi1: background thread "ubi_bgt1d" started, PID 93
[    3.008266] block ubiblock0_1: created from ubi0:1(rootfs)
[    3.015216] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    3.024170] ALSA device list:
[    3.027114]   No soundcards found.
[    3.035579] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    3.045289] devtmpfs: mounted
[    3.051036] Freeing unused kernel image (initmem) memory: 1024K
[    3.057282] Run /sbin/init as init process
[    3.292226] init: Console is alive
[    4.691484] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.726023] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.744227] init: - preinit -
[    5.303998] random: crng init done
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.201906] SWUPDATE: AT91Bootstrap version 4.0.5-gitAUTOINC+8fe4b67188-r0.tano3.2
[    9.574360] SWUPDATE: U-Boot version 2020.01-gitAUTOINC+af59b26c22-tano0.3
[    9.682875] SWUPDATE: U-Boot startup version 1.0.0-tano1.atmel1
[    9.723168] SWUPDATE: Kernel version 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.1.20.0.1
[    9.759942] SWUPDATE: Read-only filesystem version 2024-04-04-20-52-51-UTC
[   10.044923] mount_root: loading kmods from internal overlay
[   10.412570] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.424542] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   10.569567] UBIFS (ubi1:0): default file-system created
[   10.575488] UBIFS (ubi1:0): Mounting in unauthenticated mode
[   10.581549] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 179
[   10.675920] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[   10.683767] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.693786] UBIFS (ubi1:0): FS size: 39616512 bytes (37 MiB, 312 LEBs), max 322 LEBs, journal size 2031616 bytes (1 MiB, 16 LEBs)
[   10.705494] UBIFS (ubi1:0): reserved for root: 1871185 bytes (1827 KiB)
[   10.712091] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID 70D8A564-67D4-40AB-A364-C74737E22CF3, small LPT model
[   10.724736] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   10.732122] block: unable to load configuration (fstab: Entry not found)
[   10.739194] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[   10.746059] block: unable to load configuration (fstab: Entry not found)
[   10.752963] block: attempting to load /etc/config/fstab
[   10.772511] block: extroot: not configured
[   10.780297] UBIFS (ubi1:0): un-mount UBI device 1
[   10.785146] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" stops
[   10.797519] UBIFS (ubi1:0): Mounting in unauthenticated mode
[   10.803529] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 180
[   10.895444] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[   10.903292] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.913308] UBIFS (ubi1:0): FS size: 39616512 bytes (37 MiB, 312 LEBs), max 322 LEBs, journal size 2031616 bytes (1 MiB, 16 LEBs)
[   10.925011] UBIFS (ubi1:0): reserved for root: 1871185 bytes (1827 KiB)
[   10.931608] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID 70D8A564-67D4-40AB-A364-C74737E22CF3, small LPT model
[   11.024589] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   11.031930] block: unable to load configuration (fstab: Entry not found)
[   11.039009] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[   11.045892] block: unable to load configuration (fstab: Entry not found)
[   11.052795] block: attempting to load /etc/config/fstab
[   11.059302] block: extroot: not configured
[   11.066114] mount_root: overlay filesystem has not been fully initialized yet
[   11.074533] mount_root: switching to ubifs overlay
[   11.305659] Root filesystem mounted
[   13.849468] urandom-seed: Seed file not found (/etc/urandom.seed)
[   13.948866] procd: - ubus -
[   14.127794] procd: - init -
Please press Enter to activate this console.
[   18.124164] kmodloader: loading kernel modules from /etc/modules.d/*
[   18.179915] tun: Universal TUN/TAP device driver, 1.6
[   18.386046] atmel_usba_udc 500000.gadget: MMIO registers at [mem 0xf8030000-0xf8033fff] mapped at a1f04173
[   18.395912] atmel_usba_udc 500000.gadget: FIFO at [mem 0x00500000-0x005fffff] mapped at 906ae1a6
[   18.438502] usbcore: registered new interface driver cdc_wdm
[   18.515175] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   18.838420] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   18.857797] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[   18.866323] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[   18.875026] cfg80211: failed to load regulatory.db
[   18.905558] cryptodev: loading out-of-tree module taints kernel.
[   18.934486] cryptodev: driver 1.12 loaded.
[   18.945468] gre: GRE over IPv4 demultiplexor driver
[   19.152074] PPTP driver version 0.8.5
[   19.289198] xt_time: kernel timezone is +0300
[   19.308070] usbcore: registered new interface driver cdc_ether
[   19.328823] usbcore: registered new interface driver cdc_ncm
[   19.423405] usbcore: registered new interface driver qmi_wwan
[   19.517657] usbcore: registered new interface driver cdc_mbim
[   19.543507] kmodloader: done loading kernel modules from /etc/modules.d/*
[   32.538039] Cgroup memory moving (move_charge_at_immigrate) is deprecated. Please report your usecase to linux-mm@kvack.org if you depend on this functionality.
[   37.101629] udevd[1370]: starting version 3.2.10
[   37.432056] udevd[1370]: starting eudev-3.2.10
[   74.048159] macb f0028000.ethernet eth0: PHY [f0028000.ethernet-ffffffff:07] driver [Micrel KSZ9031 Gigabit PHY] (irq=POLL)
[   74.059412] macb f0028000.ethernet eth0: configuring for phy/rgmii-rxid link mode
[   74.128174] br-lan: port 1(eth0) entered blocking state
[   74.133406] br-lan: port 1(eth0) entered disabled state
[   74.139272] device eth0 entered promiscuous mode
[   74.376861] macb f802c000.ethernet eth1: PHY [f802c000.ethernet-ffffffff:01] driver [Micrel KSZ8081 or KSZ8091] (irq=POLL)
[   74.388048] macb f802c000.ethernet eth1: configuring for phy/rmii link mode
[   77.286279] macb f0028000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   77.324006] br-lan: port 1(eth0) entered blocking state
[   77.329240] br-lan: port 1(eth0) entered forwarding state
[   77.373996] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  106.385311] using random self ethernet address
[  106.389752] using random host ethernet address
[  106.395870] usb0: HOST MAC ce:6c:d9:23:88:b0
[  106.400138] usb0: MAC 0e:76:d9:86:cb:47
[  106.404144] using random self ethernet address
[  106.408564] using random host ethernet address
[  106.413161] g_ether gadget.0: Ethernet Gadget, version: Memorial Day 2008
[  106.420029] g_ether gadget.0: g_ether ready
[  106.595225] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready


tanowrt login: root
Password:
 _______            __          __   _
|__   __|           \ \        / /  | |    Embedded Linux Distribution
   | | __ _ _ __   __\ \  /\  / / __| |_   by Tano Systems
   | |/ _` | '_ \ / _ \ \/  \/ / '__| __|
   | | (_| | | | | (_) \  /\  /| |  | |_   (c) 2018-2024 Tano Systems LLC
   |_|\__,_|_| |_|\___/ \/  \/ |_|   \__|  https://tano-systems.com

   Board:    Atmel SAMA5D3 Xplained (NAND)
   Release:  Kirkstone
   Revision: dbf0f31465fe7494d2e3a29be655b14e5f3586d4
             2024-04-04 20:52:51 UTC

[root@tanowrt ~]#