1.12.2 SAMA5D2 Xplained Booting from Internal eMMC Flash Logs

1.12.2.1 AT91Bootstrap

AT91Bootstrap 4.0.8-gitAUTOINC+c331a16179-r0.tano3.2 (2023-12-18 09:57:32)

EEPROM: Loading AT24xx information ...
EEPROM: BoardName | [Revid] | VendorName
  #0  SAMA5D2-XULT [AB1]      ATMEL-RF0
EEPROM: BoardDate | Year | Week
EEPROM:             2016    22

EEPROM: Board sn: 0xd300000 revision: 0x400000

SD/MMC: Image: Read file u-boot.bin to 0x26f00000
MMC: ADMA supported
MMC: Specification Version 4.0 or higher
MMC: v5.0/5.01 detected
MMC: highspeed supported
MMC: Dual Data Rate supported
MMC: detecting buswidth...
MMC: 8-bit bus width detected
SD/MMC: Done to load image
<debug_uart>

1.12.2.2 U-Boot

U-Boot 2023.07.02-gitAUTOINC+842d9d53a1-tano0.3 (Dec 18 2023 - 10:10:05 +0000)

CPU:   SAMA5D27-CU
Crystal frequency:       12 MHz
CPU clock        :      498 MHz
Master clock     :      166 MHz

DRAM:  512 MiB
Core:  138 devices, 22 uclasses, devicetree: separate
MMC:   sdio-host@a0000000: 0, sdio-host@b0000000: 1
Loading Environment from MMC... OK
In:    serial@f8020000
Out:   serial@f8020000
Err:   serial@f8020000
Net:   
Warning: ethernet@f8008000 MAC addresses don't match:
Address in ROM is00:10:a1:98:97:02
Address in environment isfc:c2:3d:02:f4:39
eth0: ethernet@f8008000
Hit any key to stop autoboot:  3  2  1  0 
switch to partitions #0, OK
mmc0(part 0) is current device

MMC read: dev # 0, block # 512, count 256 ... 256 blocks read: OK
## Executing script at 21000000
Board name: sama5d2_xplained
Active system A
Loading kernel fitImage...
switch to partitions #0, OK
mmc0(part 0) is current device
6077544 bytes read in 364 ms (15.9 MiB/s)
Booting kernel 0x24000000#conf-at91-sama5d2_xplained.dtb...
## Loading kernel from FIT Image at 24000000 ...
   Using 'conf-at91-sama5d2_xplained.dtb' configuration
   Trying 'kernel-1' kernel subimage
     Description:  Linux kernel
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x24000118
     Data Size:    6039872 Bytes = 5.8 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x22000000
     Entry Point:  0x22000000
     Hash algo:    sha256
     Hash value:   5270cd1c1ed37581683a7104485043f18e1b6914bad94b7470e57b8cd7a54bb3
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 24000000 ...
   Using 'conf-at91-sama5d2_xplained.dtb' configuration
   Trying 'fdt-at91-sama5d2_xplained.dtb' fdt subimage
     Description:  Flattened Device Tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x245c2b70
     Data Size:    35679 Bytes = 34.8 KiB
     Architecture: ARM
     Load Address: 0x23e00000
     Hash algo:    sha256
     Hash value:   dc0e9da9666471b673397a949d45df63f53d6276bd32946c510797ebb3564750
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x245c2b70 to 0x23e00000
   Booting using the fdt blob at 0x23e00000
Working FDT set to 23e00000
   Loading Kernel Image
   Loading Device Tree to 3eb40000, end 3eb4bb5e ... OK
Working FDT set to 3eb40000

Starting kernel ...

1.12.2.3 Linux Kernel (OS)

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.1.20.0.1 (oe-user@oe-host) (arm-oe-linux-gnueabi-gcc (GCC) 11.4.0, GNU ld (GNU Binutils) 2.38.20220708) #1 Tue Jan 23 16:07:43 UTC 2024
[    0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Atmel SAMA5D2 Xplained
[    0.000000] Memory policy: Data cache writeback
[    0.000000] cma: Reserved 16 MiB at 0x3e800000
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000020000000-0x000000003fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000020000000-0x000000003fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000003fffffff]
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129920
[    0.000000] Kernel command line: console=ttyS0,115200n8  root=/dev/mmcblk0p3 ro rootfstype=squashfs rootwait rootfs_partition=3 rootfs_volume=3 earlyprintk panic=15
[    0.000000] Unknown kernel command line parameters "earlyprintk rootfs_partition=3 rootfs_volume=3", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 488740K/524288K available (9216K kernel code, 461K rwdata, 2336K rodata, 1024K init, 168K bss, 19164K reserved, 16384K cma-reserved)
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] L2C-310 ID prefetch enabled, offset 2 lines
[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000] L2C-310 cache controller enabled, 8 ways, 128 kB
[    0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x36020000
[    0.000000] clocksource: timer@f800c000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 184217874325 ns
[    0.000003] sched_clock: 32 bits at 10MHz, resolution 96ns, wraps every 206986376143ns
[    0.000042] Switching to timer-based delay loop, resolution 96ns
[    0.000304] clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 11513617062 ns
[    0.001110] Console: colour dummy device 80x30
[    0.001209] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.75 BogoMIPS (lpj=103750)
[    0.001245] CPU: Testing write buffer coherency: ok
[    0.001349] pid_max: default: 32768 minimum: 301
[    0.001774] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001823] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.005426] Setting up static identity map for 0x20100000 - 0x20100060
[    0.006911] devtmpfs: initialized
[    0.020995] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[    0.021534] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.021587] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.023375] pinctrl core: initialized pinctrl subsystem
[    0.026514] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.029215] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.031947] cpuidle: using governor menu
[    0.059143] AT91: PM: standby: standby, suspend: ulp0
[    0.082682] at_xdmac f0010000.dma-controller: 16 channels, mapped at 0x(ptrval)
[    0.086131] at_xdmac f0004000.dma-controller: 16 channels, mapped at 0x(ptrval)
[    0.087747] AT91: Detected SoC family: sama5d2
[    0.087770] AT91: Detected SoC: sama5d27, revision 1
[    0.089054] SCSI subsystem initialized
[    0.089707] usbcore: registered new interface driver usbfs
[    0.089848] usbcore: registered new interface driver hub
[    0.089964] usbcore: registered new device driver usb
[    0.091245] mc: Linux media interface: v0.10
[    0.091410] videodev: Linux video capture interface: v2.00
[    0.091561] pps_core: LinuxPPS API ver. 1 registered
[    0.091576] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.091627] PTP clock support registered
[    0.092259] Advanced Linux Sound Architecture Driver Initialized.
[    0.093530] Bluetooth: Core ver 2.22
[    0.093689] NET: Registered PF_BLUETOOTH protocol family
[    0.093704] Bluetooth: HCI device and connection manager initialized
[    0.093735] Bluetooth: HCI socket layer initialized
[    0.093753] Bluetooth: L2CAP socket layer initialized
[    0.093796] Bluetooth: SCO socket layer initialized
[    0.095315] clocksource: Switched to clocksource timer@f800c000
[    0.122625] NET: Registered PF_INET protocol family
[    0.123210] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.126109] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.126199] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.126252] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.126349] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.126507] TCP: Hash tables configured (established 4096 bind 4096)
[    0.126765] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.126826] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.127240] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.128556] RPC: Registered named UNIX socket transport module.
[    0.128590] RPC: Registered udp transport module.
[    0.128599] RPC: Registered tcp transport module.
[    0.128606] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.130096] Initialise system trusted keyrings
[    0.131020] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    0.131991] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.345538] Key type asymmetric registered
[    0.345576] Asymmetric key parser 'x509' registered
[    0.345727] io scheduler mq-deadline registered
[    0.345752] io scheduler kyber registered
[    0.358762] pinctrl-at91-pio4 fc038000.pinctrl: atmel pinctrl initialized
[    0.381240] brd: module loaded
[    0.397527] loop: module loaded
[    0.399292] atmel_usart_serial.0.auto: ttyS0 at MMIO 0xf8020000 (irq = 152, base_baud = 5187500) is a ATMEL_SERIAL
[    0.975760] printk: console [ttyS0] enabled
[    0.982611] atmel_usart_serial.1.auto: ttyS1 at MMIO 0xfc008000 (irq = 153, base_baud = 5187500) is a ATMEL_SERIAL
[    0.996968] at91_i2c fc018600.i2c: can't get DMA channel, continue without DMA support
[    1.004854] at91_i2c fc018600.i2c: Using FIFO (16 data)
[    1.010539] i2c i2c-3: using pinctrl states for GPIO recovery
[    1.016426] i2c i2c-3: using generic GPIOs for recovery
[    1.021761] at91_i2c fc018600.i2c: AT91 i2c bus driver (hw version: 0x704).
[    1.033885] atmel_spi f8000000.spi: Using dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers
[    1.042586] atmel_spi f8000000.spi: Using FIFO (16 data)
[    1.050243] spi-nor spi0.0: at25df321a (4096 Kbytes)
[    1.059082] atmel_spi f8000000.spi: Atmel SPI Controller version 0x311 at 0xf8000000 (irq 155)
[    1.071125] CAN device driver interface
[    1.082138] macb f8008000.ethernet eth0: Cadence GEM rev 0x00020203 at 0xf8008000 irq 156 (fc:c2:3d:02:f4:39)
[    1.093108] PPP generic driver version 2.4.2
[    1.098516] PPP MPPE Compression module registered
[    1.103277] NET: Registered PF_PPPOX protocol family
[    1.109005] atmel-ehci 500000.ehci: EHCI Host Controller
[    1.114337] atmel-ehci 500000.ehci: new USB bus registered, assigned bus number 1
[    1.122446] atmel-ehci 500000.ehci: irq 159, io mem 0x00500000
[    1.155395] atmel-ehci 500000.ehci: USB 2.0 started, EHCI 1.00
[    1.161569] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    1.169852] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.177042] usb usb1: Product: EHCI Host Controller
[    1.181872] usb usb1: Manufacturer: Linux 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.1.20.0.1 ehci_hcd
[    1.191439] usb usb1: SerialNumber: 500000.ehci
[    1.197597] hub 1-0:1.0: USB hub found
[    1.201403] hub 1-0:1.0: 3 ports detected
[    1.208685] at91_ohci 400000.ohci: USB Host Controller
[    1.213858] at91_ohci 400000.ohci: new USB bus registered, assigned bus number 2
[    1.221851] at91_ohci 400000.ohci: irq 159, io mem 0x00400000
[    1.299720] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[    1.308008] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.315168] usb usb2: Product: USB Host Controller
[    1.319968] usb usb2: Manufacturer: Linux 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.1.20.0.1 ohci_hcd
[    1.329503] usb usb2: SerialNumber: at91
[    1.334879] hub 2-0:1.0: USB hub found
[    1.338786] hub 2-0:1.0: 3 ports detected
[    1.345094] usbcore: registered new interface driver cdc_acm
[    1.350807] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.359035] usbcore: registered new interface driver usb-storage
[    1.365231] usbcore: registered new interface driver usbserial_generic
[    1.371845] usbserial: USB Serial support registered for generic
[    1.377923] usbcore: registered new interface driver ftdi_sio
[    1.383677] usbserial: USB Serial support registered for FTDI USB Serial Device
[    1.394144] at91_rtc f80480b0.rtc: registered as rtc0
[    1.399302] at91_rtc f80480b0.rtc: setting system clock to 2012-01-01T00:00:09 UTC (1325376009)
[    1.408035] at91_rtc f80480b0.rtc: AT91 Real Time Clock driver.
[    1.414265] i2c_dev: i2c /dev entries driver
[    1.420340] at91-reset f8048000.reset-controller: Starting after wakeup
[    1.430004] sama5d4_wdt f8048040.watchdog: initialized (timeout = 16 sec, nowayout = 0)
[    1.438818] Bluetooth: HCI UART driver ver 2.3
[    1.443217] Bluetooth: HCI UART protocol H4 registered
[    1.448531] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    1.454898] usbcore: registered new interface driver btusb
[    1.461065] sdhci: Secure Digital Host Controller Interface driver
[    1.467249] sdhci: Copyright(c) Pierre Ossman
[    1.471780] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.479644] ledtrig-cpu: registered to indicate activity on CPUs
[    1.486335] atmel_aes f002c000.crypto: version: 0x500
[    1.495042] atmel_aes f002c000.crypto: Atmel AES - Using dma0chan2, dma0chan3 for DMA transfers
[    1.504844] atmel_sha f0028000.crypto: version: 0x510
[    1.512043] atmel_sha f0028000.crypto: using dma0chan4 for DMA transfers
[    1.519108] atmel_sha f0028000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512
[    1.527442] atmel_tdes fc044000.crypto: version: 0x703
[    1.533392] atmel_tdes fc044000.crypto: using dma0chan5, dma0chan6 for DMA transfers
[    1.541507] atmel_tdes fc044000.crypto: Atmel DES/TDES
[    1.547379] usbcore: registered new interface driver usbhid
[    1.552905] usbhid: USB HID core driver
[    1.562832] atmel-classd fc048000.classd: PWM modulation type is Differential, non-overlapping is enabled
[    1.573009] mmc0: SDHCI controller on a0000000.sdio-host [a0000000.sdio-host] using ADMA
[    1.584502] u32 classifier
[    1.587234]     input device check on
[    1.590829]     Actions configured
[    1.594886] NET: Registered PF_INET6 protocol family
[    1.603141] Segment Routing with IPv6
[    1.607028] In-situ OAM (IOAM) with IPv6
[    1.611089] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.618640] NET: Registered PF_PACKET protocol family
[    1.623800] Bridge firewalling registered
[    1.627852] can: controller area network core
[    1.632350] NET: Registered PF_CAN protocol family
[    1.637162] can: raw protocol
[    1.640078] can: broadcast manager protocol
[    1.644245] can: netlink gateway - max_hops=1
[    1.649569] Bluetooth: RFCOMM TTY layer initialized
[    1.654495] Bluetooth: RFCOMM socket layer initialized
[    1.659685] Bluetooth: RFCOMM ver 1.11
[    1.663432] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    1.668728] Bluetooth: BNEP filters: protocol multicast
[    1.673910] Bluetooth: BNEP socket layer initialized
[    1.678874] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.684747] Bluetooth: HIDP socket layer initialized
[    1.689770] l2tp_core: L2TP core driver, V2.0
[    1.694082] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[    1.698863] l2tp_netlink: L2TP netlink interface
[    1.704741] Loading compiled-in X.509 certificates
[    1.752054] at91_i2c f8028000.i2c: can't get DMA channel, continue without DMA support
[    1.760058] at91_i2c f8028000.i2c: Using FIFO (16 data)
[    1.766185] i2c i2c-0: using pinctrl states for GPIO recovery
[    1.772075] i2c i2c-0: using generic GPIOs for recovery
[    1.800200] mmc0: new DDR MMC card at address 0001
[    1.807848] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB
[    1.820598]  mmcblk0: p1 p2 p3 p4 < p5 p6 p7 >
[    1.829528] at91_i2c f8028000.i2c: AT91 i2c bus driver (hw version: 0x704).
[    1.837677] at91_i2c fc028000.i2c: can't get DMA channel, continue without DMA support
[    1.845656] at91_i2c fc028000.i2c: Using FIFO (16 data)
[    1.853580] mmcblk0boot0: mmc0:0001 Q2J54A 16.0 MiB
[    1.862721] mmcblk0boot1: mmc0:0001 Q2J54A 16.0 MiB
[    1.871198] mmcblk0rpmb: mmc0:0001 Q2J54A 512 KiB, chardev (247:0)
[    1.877893] i2c i2c-1: using pinctrl states for GPIO recovery
[    1.883726] i2c i2c-1: using generic GPIOs for recovery
[    1.889756] at24 1-0054: supply vcc not found, using dummy regulator
[    1.897727] at24 1-0054: 256 byte 24c02 EEPROM, writable, 16 bytes/write
[    1.904582] at91_i2c fc028000.i2c: AT91 i2c bus driver (hw version: 0x704).
[    1.921298] at91-sama5d2_adc fc030000.adc: setting up trigger as external_rising
[    1.928785] at91-sama5d2_adc fc030000.adc: version: 800
[    1.936781] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    1.946243] ALSA device list:
[    1.949179]   #0: CLASSD
[    1.952544] atmel_usart_serial atmel_usart_serial.0.auto: using dma0chan8 for rx DMA transfers
[    1.962119] atmel_usart_serial atmel_usart_serial.0.auto: using dma0chan9 for tx DMA transfers
[    2.006370] mmc1: SDHCI controller on b0000000.sdio-host [b0000000.sdio-host] using ADMA
[    2.027629] VFS: Mounted root (squashfs filesystem) readonly on device 179:3.
[    2.037249] devtmpfs: mounted
[    2.043130] Freeing unused kernel image (initmem) memory: 1024K
[    2.049355] Run /sbin/init as init process
[    2.186891] init: Console is alive
[    2.190830] init: - watchdog -
[    3.176923] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.209557] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.227828] init: - preinit -
[    6.255361] random: crng init done
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.854461] SWUPDATE: AT91Bootstrap version 4.0.5-gitAUTOINC+8fe4b67188-r0.tano3.2
[   10.007062] SWUPDATE: U-Boot version 2020.01-gitAUTOINC+af59b26c22-tano0.3
[   10.115888] SWUPDATE: U-Boot startup version 1.0.0-tano1.atmel1
[   10.145901] SWUPDATE: Kernel version 6.1.74-tano-mchp-standard-g3f74b634cc-tano0.2.1.20.0.1
[   10.184215] SWUPDATE: Read-only filesystem version 2024-04-04-21-31-45-UTC
[   10.376128] mount_root: /dev/mmcblk0p1: p1, rw, start 1048576, size 8388608
[   10.387513] mount_root: /dev/mmcblk0p2: p2, rw, start 9437184, size 134217728
[   10.395456] mount_root: /dev/mmcblk0p3: p3, rw, start 143654912, size 1073741824 [rootfs]
[   10.405082] mount_root: /dev/mmcblk0p4: p4, rw, start 1217396736, size 1024
[   10.416364] mount_root: /dev/mmcblk0p5: p5, rw, start 1218445312, size 134217728
[   10.425766] mount_root: /dev/mmcblk0p6: p6, rw, start 1353711616, size 1073741824
[   10.437487] mount_root: /dev/mmcblk0p7: p7, rw, start 2428502016, size 1421869056 [overlay]
[   10.446175] mount_root: root filesystem on the /dev/mmcblk0p3 partition of /dev/mmcblk0 (rw) device
[   10.471679] mount_root: founded suitable overlay partition /dev/mmcblk0p7
[   10.482817] mount_root: loading kmods from internal overlay
[   10.809340] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.829193] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   11.027625] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Quota mode: disabled.
[   11.037242] block: attempting to load /tmp/ext4_cfg/upper/etc/config/fstab
[   11.045900] block: unable to load configuration (fstab: Entry not found)
[   11.052777] block: attempting to load /tmp/ext4_cfg/etc/config/fstab
[   11.059555] block: unable to load configuration (fstab: Entry not found)
[   11.066544] block: attempting to load /etc/config/fstab
[   11.081774] block: extroot: not configured
[   11.087954] EXT4-fs (mmcblk0p7): unmounting filesystem.
[   11.109267] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Quota mode: disabled.
[   11.242090] block: attempting to load /tmp/ext4_cfg/upper/etc/config/fstab
[   11.249526] block: unable to load configuration (fstab: Entry not found)
[   11.256535] block: attempting to load /tmp/ext4_cfg/etc/config/fstab
[   11.263147] block: unable to load configuration (fstab: Entry not found)
[   11.270144] block: attempting to load /etc/config/fstab
[   11.276475] block: extroot: not configured
[   11.283681] mount_root: overlay filesystem has not been fully initialized yet
[   11.296962] mount_root: switching to ext4 overlay
[   11.509028] Root filesystem mounted
[   13.637452] urandom-seed: Seed file not found (/etc/urandom.seed)
[   13.702008] procd: - watchdog -
[   13.715692] procd: - ubus -
[   13.801771] procd: - init -
Please press Enter to activate this console.
[   17.461078] kmodloader: loading kernel modules from /etc/modules.d/*
[   17.517394] tun: Universal TUN/TAP device driver, 1.6
[   17.744619] atmel_usba_udc 300000.gadget: MMIO registers at [mem 0xfc02c000-0xfc02c3ff] mapped at d851d58e
[   17.754470] atmel_usba_udc 300000.gadget: FIFO at [mem 0x00300000-0x003fffff] mapped at 0853c96e
[   17.805803] usbcore: registered new interface driver cdc_wdm
[   17.897473] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   18.150667] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   18.169600] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[   18.178162] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[   18.186824] cfg80211: failed to load regulatory.db
[   18.217059] cryptodev: loading out-of-tree module taints kernel.
[   18.246173] cryptodev: driver 1.12 loaded.
[   18.260513] gre: GRE over IPv4 demultiplexor driver
[   18.488081] PPTP driver version 0.8.5
[   18.639876] xt_time: kernel timezone is +0400
[   18.659780] usbcore: registered new interface driver cdc_ether
[   18.690540] usbcore: registered new interface driver cdc_ncm
[   18.793137] usbcore: registered new interface driver qmi_wwan
[   18.888591] usbcore: registered new interface driver cdc_mbim
[   18.928709] kmodloader: done loading kernel modules from /etc/modules.d/*
[   30.777994] Cgroup memory moving (move_charge_at_immigrate) is deprecated. Please report your usecase to linux-mm@kvack.org if you depend on this functionality.
[   34.488913] udevd[1367]: starting version 3.2.10
[   34.668005] udevd[1367]: starting eudev-3.2.10
[   67.915712] macb f8008000.ethernet eth0: PHY [f8008000.ethernet-ffffffff:01] driver [Micrel KSZ8081 or KSZ8091] (irq=97)
[   67.955632] macb f8008000.ethernet eth0: configuring for phy/rmii link mode
[   67.993401] br-lan: port 1(eth0) entered blocking state
[   67.998689] br-lan: port 1(eth0) entered disabled state
[   68.004399] device eth0 entered promiscuous mode
[   70.311658] macb f8008000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[   70.386724] br-lan: port 1(eth0) entered blocking state
[   70.391941] br-lan: port 1(eth0) entered forwarding state
[   70.441280] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   95.918492] using random self ethernet address
[   95.922916] using random host ethernet address
[   95.929105] usb0: HOST MAC 52:07:a0:26:16:6d
[   95.933353] usb0: MAC 12:87:7d:65:e1:ef
[   95.937334] using random self ethernet address
[   95.941718] using random host ethernet address
[   95.946319] g_ether gadget.0: Ethernet Gadget, version: Memorial Day 2008
[   95.953054] g_ether gadget.0: g_ether ready
[   96.132405] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready